Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Tue Mar 19, 2024 1:31 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 29 posts ]  Go to page 1, 2  Next
Author Message
PostPosted: Fri May 23, 2008 11:46 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
OK, I have started my #2 Classical Build. It will be the same basic design as #1, but will be built from EIR and German Spruce, and will have a HOG V-Joint Neck - Maybe [headinwall] .

If you are interested, you can stay with me, but it's lots of pictures, and some explanations. I am learning and having fun at the same time. I'm also learning the secrets of some of my tools. bliss

Using the J. French method, I layed out my V-Joint (first of several :roll: ) So here we go.

First, I leveled out a neck blank that was a little too thin, anyway, but thought, this is a first, so I'll use a little less angle on the head. I could get a good 11* with this thickness, which was a fat 1" (26mm).
Attachment:
P1000804 (Large).JPG
Attachment:
P1000805 (Large).JPG

Next, I leveled up a head piece just over 3"wide, thicknessed eventually to a fat 16mm, to allow for a Head plate, and back plate to end up at about 20 - 21mm.
Attachment:
P1000810 (Large).JPG

Measured carefully, and clamped the ruler down to scribe the lines, deeply with an scribing knife (homemade from a heavy duty hacksaw blade).
Attachment:
P1000812 (Large).JPG

OK, so I scribed through the V gaah , it won't matter, it'll be snaded, and end up under the nut.
Attachment:
P1000815 (Large).JPG

Cutting bevels carefully to the lines only in the waste areas. This will create good guides for sawing.
Attachment:
P1000816 (Large).JPG
Attachment:
P1000817 (Large).JPG
Attachment:
P1000818 (Large).JPG

Much more to come in next post.


You do not have the required permissions to view the files attached to this post.

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
PostPosted: Fri May 23, 2008 11:58 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
Moving right along.

Still beveling to the lines.
Attachment:
P1000821 (Large).JPG

Now, sawing close to the lines, but not to them all the way, but they are easy to see, because of the bevels.
Attachment:
P1000822 (Large).JPG
Attachment:
P1000823 (Large).JPG

So, you end up with joints that need trimming with a chisel, to clean them up, but the lines are still visible, except where I got to close [headinwall] .
Attachment:
P1000824 (Large).JPG

Here is the head piece cut out with the female V cut. Yeah, I marked it wrong, but it'll be covered up by the head plate. Wjhat's it to ya? pfft
Attachment:
P1000826 (Large).JPG

Gluing up.
Attachment:
P1000831 (Large).JPG

Not terrible for a first, right?
Attachment:
P1000836 (Large).JPG

Next, I glued up the heel block pieces.
Attachment:
P1000859 (Large).JPG

We still have a long way to go - hang on if you aren't too bored! Eat Drink


You do not have the required permissions to view the files attached to this post.

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
PostPosted: Fri May 23, 2008 12:14 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
Hey, this is easy! :D We're screaming along.
Attachment:
P1000866 (Large).JPG

Roughed in the inside cut for the Spanish foot.
Attachment:
P1000869 (Large).JPG

There has to be a way to cut the slots on a table saw. Lets try a method. I made a sled with a 7* slant on it, which is the slope of the V inside the slots. The slots are cut at 4*, so the sled will slide using the Miter slide on the table saw. Great idea. Here's the first cut. Just needs to be a smidgen wider.
Attachment:
P1000870 (Large).JPG

First side went great. Second side, was not perfectly square, and I tried to fix it, but failed miserably! oops_sign So much for this neck. Maybe I'll save it for a short scale guitar.
Attachment:
P1000871 (Large).JPG
Attachment:
P1000872 (Large).JPG


Starting Over now with a new neck blank. This one is actually better, and is a full 1 1/8" thick to allow for a 14* angle on the head. To help, I thought, I made a template to use for marking.
Attachment:
P1000874 (Large).JPG

Marks look fairly good.
Attachment:
P1000875 (Large).JPG

Did my bevel cutting per the plan.
Attachment:
P1000876 (Large).JPG


Still more coming - grab a snack pizza !


You do not have the required permissions to view the files attached to this post.

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
PostPosted: Fri May 23, 2008 12:14 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Mar 22, 2007 10:59 pm
Posts: 2103
Location: Bucharest, Romania
Country: Romania
Focus: Build
Status: Professional
:D aaah mhhm are you *sure* that thing is going to hold when you actually put strings on it? :D

_________________
Build log


Top
 Profile  
 
PostPosted: Fri May 23, 2008 12:24 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
Here's a couple of shots showing all the bevels cut.
Attachment:
P1000878 (Large).JPG
Attachment:
P1000879 (Large).JPG

It was about here, that I was looking at the V and thinking it didn't look right. I re-measured, and realized I had made my Template with the wrong measurements. It would have been OK, as it was only 2mm too long, but it also wasn't quite square, so I cut off the marked head piece and re-marked with measured and scribed on a ruler again. I think the template was slipping when I marked, or bending at the tip. Live and learn! duh
Attachment:
P1000880 (Large).JPG

Cutting the bevels.
Attachment:
P1000881 (Large).JPG
Attachment:
P1000882 (Large).JPG
Attachment:
P1000883 (Large).JPG
Attachment:
P1000884 (Large).JPG

Then cut with a saw, not to the line, this time.
Attachment:
P1000885 (Large).JPG


Still more to come.


You do not have the required permissions to view the files attached to this post.

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
PostPosted: Fri May 23, 2008 12:38 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
Are we totally bored out of our skulls yet? beehive idunno

Carefully using a chisel, I shaved off the excess, working with the grain, and shaving to the lines, keeping the chisel as level as possible, sort of using it like a plane. If I had thought about it, I would have turned the neck the other way, then chiseling would have been easier. It is something to think about when doing this. Define the direction of the grain before deciding which end you are going to saw down and chisel on. I had to chisel at a bevel from the shoulder up to the point of the bevel. It would have been easier if I could have worked down to the shoulder, instead. More learning! [:Y:]
Attachment:
P1000886 (Large).JPG
Attachment:
P1000888 (Large).JPG
Attachment:
P1000889 (Large).JPG

OK, I'm real close on the V now, still have the shoulders to go.
Attachment:
P1000890 (Large).JPG

The chip outs here won't matter, as they will be eventually cut off.
Attachment:
P1000891 (Large).JPG

Oh No! This will not do. wow7-eyes Start over on this part of the V.
Attachment:
P1000892 (Large).JPG

I remeasured, and re-marked, and re-cut, and re-beveled, and finally got a fit. You can see the lines where I started over. Good thing I had a long blank.
Attachment:
P1000904 (Large).JPG

Here you can see the head and the V ready to be glued.
Attachment:
P1000905 (Large).JPG

One more to go, almost done.


You do not have the required permissions to view the files attached to this post.

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
PostPosted: Fri May 23, 2008 12:54 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
Checking the fit.
Attachment:
P1000908 (Large).JPG
Attachment:
P1000910 (Large).JPG

Gluing up.
Attachment:
P1000911 (Large).JPG

All glued.
Attachment:
P1000915 (Large).JPG

The V planed down to the head, with the joint under the nut area. Not perfect, but passable, I think.
Attachment:
P1000918 (Large).JPG

The head piece was a little thick anyway, and I was a little too close on the back side. I found a good use for the littel bull nosed plane from Lee Valley. It gets right in there to clean up behind chiseling the back of the head down.
Attachment:
P1000919 (Large).JPG

Finally, here, gluing the heel blocks on.
Attachment:
P1000922 (Large).JPG


That's all for now. Go rest. After this coming weekend, I hope to have the neck slotted and me ready to move on to other things. I also have a scarf neck going for #3 at the same time I'm doing this one. Thanks for looking at the trials and tribulations of the beginner's V-Neck.


You do not have the required permissions to view the files attached to this post.

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
PostPosted: Fri May 23, 2008 1:01 pm 
Offline
Koa
Koa

Joined: Tue Mar 07, 2006 12:10 am
Posts: 606
Location: United States
Waddy,

Great pics, looks good, nice fit. I'm learning the v-neck joint as well. We're at the same spot in our build, I'll post my v-neck attempt, you can have a look.


Top
 Profile  
 
PostPosted: Fri May 23, 2008 1:19 pm 
Offline
Koa
Koa
User avatar

Joined: Wed Mar 29, 2006 11:21 am
Posts: 805
Location: United States
First name: Jim Howell
Waddy--

Thanks for posting the pics on the V-neck. [clap] [clap] This is a very nice toot on cutting the joint and I think a very nice way to get a mahogany neck out of thinner pieces of wood. I'm going to try this on my next steel string. Got some poplar from the Borg to practice on.

_________________
Jim Howell
Charlotte, NC


Top
 Profile  
 
PostPosted: Fri May 23, 2008 2:03 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
Probably a good idea. I just figured that practicing on HOG would get me familiar with how that wood works, and the idiosyncrasies of that particular wood. I had bought a whole bolt of neck blank rejects from Hibdon last year, and it has some good stuff in it, so I have a lot of practice wood. I have to work around some worm holes and knots, and some is not perfectly quartered, but I have found much that is, perfect after cutting to the needed lengths.

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
PostPosted: Fri May 23, 2008 2:21 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Aug 26, 2005 5:49 pm
Posts: 2915
Location: Norway
Good job, Waddy! I have never made one of those joints, but I've been meaning to. It's good to learn what to look out for, I'm sure I can invent some new ways to mess up the process though.

I don't know exactly what went wrong with the table saw heel block slot cutting jig thingy; how are you going to cut those slots this time?

_________________
Rian Gitar og Mandolin


Top
 Profile  
 
PostPosted: Fri May 23, 2008 2:37 pm 
Offline
Koa
Koa

Joined: Tue Mar 07, 2006 12:10 am
Posts: 606
Location: United States
Waddy, are you making your jig to do the Romanillos style wedge heel slots? I have a table saw jig for conventional heel slots but I'm trying to de-jig as much as possible. I was thinking of switching to the Romanillos style slots because they look more forgiving to cut with a hand saw. Am I wrong? Are the Romanillos style slots difficult to cut freehand?


Top
 Profile  
 
PostPosted: Fri May 23, 2008 2:49 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
I did them freehand on my first one, but thought it would be nice to be able to do it neatly and quickly on a table saw, instead of having to hog out all that material with a chisel. The problem I had doing it by hand was 1) getting a perfectly straight saw line (Dave LaPlante's Jig would solve the problem for hand cutting - see - [img=http://www.luthiersforum.com/forum/viewtopic.php?f=10101&t=16461&hilit=neck]Working Up a Classical Neck[/img] post), 2) having a perfectly flat V in the center for the wedges to but up against for a good glue joint on the inside. (don't know how important that is) and 3) having the two cuts perfectly parallel, so the wedges can be easily fit to the slot.

Here is a thought I just had while typing my response to you. Maybe it would help to use the same approach used for the V-joint, i.e., cut bevels into a scored line before doing the saw cut. That would give you a much better guide for hand cutting. Hmmmm! I may try that. Then you could chisel to the line just like with the V. What do you think?

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
PostPosted: Fri May 23, 2008 3:27 pm 
Offline
Koa
Koa

Joined: Tue Mar 07, 2006 12:10 am
Posts: 606
Location: United States
Sounds like a good plan. I'm definitly going to explore the idea on some practice blocks of wood. I've never done the Romanillos style heel so I at least want to give it a try. I think I remember LaPlantes jig, I'll give it another look, but what I really want to accomplish is cutting freehand heel slots with just marking tools, handsaws, and chisels while maintaining clean straight lines.


Top
 Profile  
 
PostPosted: Fri May 23, 2008 3:31 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
Marc, if you cut your slope on the inside heel first, you can then put a depth stop on the saw to control the depth of the slot. The angle would be the same as the heel angle inside the guitar.

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
PostPosted: Fri May 23, 2008 5:35 pm 
Offline
Cocobolo
Cocobolo

Joined: Sat Oct 27, 2007 1:49 pm
Posts: 144
Location: North Carolina
Really enjoyed your post. I have only made one neck and that one with a long scarf joint. I want to try the V joint an will use your pictures to go by.

Steve


Top
 Profile  
 
PostPosted: Fri May 23, 2008 7:01 pm 
Offline
Koa
Koa

Joined: Tue Mar 07, 2006 12:10 am
Posts: 606
Location: United States
Thanks for the tip Waddy.


Top
 Profile  
 
PostPosted: Fri May 23, 2008 7:11 pm 
Offline
Mahogany
Mahogany

Joined: Tue Jan 29, 2008 4:43 pm
Posts: 66
Location: USA
Waddy

I always enjoy looking at the pictures you submit. You always think through your process very carefully.

2 questions:

What is the reasoning for the V joint?


Very basic question - what is HOG wood?


Top
 Profile  
 
PostPosted: Fri May 23, 2008 7:19 pm 
Offline
Koa
Koa
User avatar

Joined: Wed Jun 08, 2005 1:00 pm
Posts: 1644
Location: United States
City: Duluth
State: MN
Country: USA
Focus: Build
Status: Amateur
Oh, Waddy, that looks difficult!

They do look elegant, but what a lot of work to get there. WTG!

Dennis

_________________
Dennis Leahy
Duluth, MN, USA
7th Sense Multimedia


Top
 Profile  
 
PostPosted: Fri May 23, 2008 8:58 pm 
Offline
Contributing Member
Contributing Member

Joined: Fri Jan 25, 2008 9:51 pm
Posts: 1134
Location: Albany NY
First name: David
Last Name: LaPlante
Status: Professional
Of course the rather hairy part here is that the actual portion of the joint that will show in the finished instrument is well within the joint and not visible in the preliminary state.
One has to check the fit in these areas closely to get a nice clean look once the neck and peghead transition are shaped.
What's even more nerve wracking is that usually one doesn't carve the neck until the guitar is completely assembled and with a classical guitar the neck is not removable if it turns out to be a disappointment.


Top
 Profile  
 
PostPosted: Fri May 23, 2008 9:24 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
Gee, thanks, David, you're making me feel real secure! :o beehive

Maybe I'll do some preliminary shaping to see what it looks like inside.. It is a good point though. I actually think my joint may be better on the inside than on the outside, but I sure don't know. I know it's not perfect, though, and that does give me some pause.

Sam, the reason for the V-Joint is really to punish myself for my many shortcomings. I do this instead of whipping myself. I'm not big on the pain thing. Nah, the real reason is because it's a beautiful joint, and because it is a repairable joint that can be fixed if someone knocks a guitar over and it hits on the head, it will pop loose at the joint, and can often be re-glued without too many issues.

HOG is slang for Honduran Mahogany.

Dennis, it is a lot of work, but why not learn when I'm learning. I did my first the easy way.

Steve - Only use the parts where it worked! Leave out the mistakes! :D Joshua's tutorial and David's post also are a big help.

Thanks for looking everyone.

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
PostPosted: Fri May 23, 2008 9:33 pm 
Offline
Contributing Member
Contributing Member

Joined: Fri Jan 25, 2008 9:51 pm
Posts: 1134
Location: Albany NY
First name: David
Last Name: LaPlante
Status: Professional
Don't sweat it Waddy, it looks good in the pics and if your sense of the fit was good as you did it you are probably right that it will look even cleaner once shaped.
In any event it will be worth the effort!


Best!


Top
 Profile  
 
PostPosted: Fri May 23, 2008 9:35 pm 
Offline
Walnut
Walnut
User avatar

Joined: Sat Jan 26, 2008 6:03 pm
Posts: 7
Location: Campobello, SC
I said it once and I'll say it again, "You Da Man"

_________________
We Bend the Wood, So You Can Bend the Strings


Top
 Profile  
 
PostPosted: Fri May 23, 2008 10:05 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Mar 19, 2007 7:05 am
Posts: 9191
Location: United States
First name: Waddy
Last Name: Thomson
City: Charlotte
State: NC
Focus: Build
Status: Semi-pro
I suppose we'll find out, huh? Thanks for your confidence David. Easy for you to say! :D

Red, where you been? I didn't know you could be quiet for so long. What are you working on these days? I assume Ennis Guitars Sr is you, isn't it? idunno

_________________
Waddy

Photobucket Build Album Library

Sound Clips of most of my guitars


Top
 Profile  
 
PostPosted: Sun May 25, 2008 2:18 am 
Offline
Cocobolo
Cocobolo

Joined: Fri Sep 28, 2007 6:22 pm
Posts: 204
Location: Taiwan
WaddyT wrote:
Second side, was not perfectly square, and I tried to fix it, but failed miserably! oops_sign So much for this neck. Maybe I'll save it for a short scale guitar


The vee joint on this neck looks seamless! [clap] Perhaps you can convert it to a dovetail or a bolt-on adjustable(or not) neck. I've done only two vees so far. They still hold, despite the more visable seams without any clamping. :oops:


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 29 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 30 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com