Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Fri Mar 29, 2024 2:53 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 23 posts ] 
Author Message
PostPosted: Sat Jul 08, 2017 10:31 pm 
Offline
Koa
Koa

Joined: Mon Feb 13, 2012 8:49 pm
Posts: 952
First name: peter
Last Name: havriluk
City: granby
State: ct
Zip/Postal Code: 06035
Country: usa
Focus: Build
Status: Amateur
Being in need of a bridge plate, I found in my woodpile a nice piece of 1/8" thick maple, flatsawn. Any reason why some of that can't be used for bridge plates? Commercial maple bridge plates, at least the ones I found, are quartersawn and .100" thick. Swapping the quartersawn for flatsawn but .025" thicker makes some intuitive sense, but does it make luthier's sense?

Thanks, folks.

_________________
Peter Havriluk



These users thanked the author phavriluk for the post: askins (Sun Jul 09, 2017 10:31 am)
Top
 Profile  
 
PostPosted: Sun Jul 09, 2017 2:49 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Jul 10, 2009 4:44 am
Posts: 5398
First name: colin
Last Name: north
Country: Scotland.
Focus: Build
Status: Semi-pro
I would think that should be fine - my current build in progress OM has a rift to flatsawn maple bridge plate at 0.09".
Not so sure that you need to make it thicker than a quarter sawn one. Not much if any difference in strength/flexibility/rigidity between quarter and flatsawn, and it would increase weight where you may not want it.

_________________
The name catgut is confusing. There are two explanations for the mix up.

Catgut is an abbreviation of the word cattle gut. Gut strings are made from sheep or goat intestines, in the past even from horse, mule or donkey intestines.

Otherwise it could be from the word kitgut or kitstring. Kit meant fiddle, not kitten.


Top
 Profile  
 
PostPosted: Sun Jul 09, 2017 3:13 am 
Offline
Koa
Koa
User avatar

Joined: Mon Sep 05, 2011 10:45 pm
Posts: 1470
First name: Trevor
Last Name: Gore
City: Sydney
Country: Australia
Focus: Build
Status: Professional
It'll likely want to curl more than quarter sawn if you glue it with a water based glue.

_________________
Trevor Gore, Luthier. Australian hand made acoustic guitars, classical guitars; custom guitar design and build; guitar design instruction.

http://www.goreguitars.com.au


Top
 Profile  
 
PostPosted: Sun Jul 09, 2017 4:40 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Jul 10, 2009 4:44 am
Posts: 5398
First name: colin
Last Name: north
Country: Scotland.
Focus: Build
Status: Semi-pro
You can always dampen the other side with water to help keep it flat. I do that with FB's.

_________________
The name catgut is confusing. There are two explanations for the mix up.

Catgut is an abbreviation of the word cattle gut. Gut strings are made from sheep or goat intestines, in the past even from horse, mule or donkey intestines.

Otherwise it could be from the word kitgut or kitstring. Kit meant fiddle, not kitten.


Top
 Profile  
 
PostPosted: Sun Jul 09, 2017 6:58 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Tue May 13, 2008 10:44 am
Posts: 6232
Location: Virginia
I don't think you need to make it thicker. If you use Titebond clamp it for 12 hours. I've never tested bridge plates but I have tested braces and they are stiffer in general then their quarter sawn counter parts. The issue with a sheet as large as a bridge plate though is the expansion would be greater with the flat sawn piece. I'm gonna guess however it's nothing to be worried about, I could be wrong. The ones I use are usually off quarter and I orient them so that the annular rings slant towards the head block in the direction of string pull. Seems to make intuitive sense. Flat sawn also seems intuitively to be better at handling the ball end string as a mounting point. A ball end might tend to want to split along the annular rings, again speculation but something to think about, or at least not worry about :)


Top
 Profile  
 
PostPosted: Sun Jul 09, 2017 9:47 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sat Dec 30, 2006 3:20 am
Posts: 2593
Location: Powell River BC Canada
First name: Danny
Last Name: Vincent
I was under the impression that Maple in the flat sawn form is what works best. I hope it's ok. I've used it on every guitar I've built. :o



These users thanked the author DannyV for the post: dpetrzelka (Sun Jul 09, 2017 11:26 pm)
Top
 Profile  
 
PostPosted: Sun Jul 09, 2017 10:08 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Jan 06, 2011 6:08 pm
Posts: 2712
First name: ernest
Last Name: kleinman
City: lee's summit
State: mo
Zip/Postal Code: 64081
Country: usa
Focus: Build
Status: Professional
Anyone else using other woods besides maple.? I have some pecan wood which seems at about the same density or slightly higher than maple , the density of pecan is roughly between eir and maple ???



These users thanked the author ernie for the post: ChuckH (Sat Jul 15, 2017 11:27 pm)
Top
 Profile  
 
PostPosted: Sun Jul 09, 2017 10:44 am 
Offline
Koa
Koa

Joined: Mon Feb 13, 2012 8:49 pm
Posts: 952
First name: peter
Last Name: havriluk
City: granby
State: ct
Zip/Postal Code: 06035
Country: usa
Focus: Build
Status: Amateur
thanks, folks. I'll sleep easy. And thin the plank down a bit.

About maple, no fixation about the species. Happened to have it, wanted to use up the stuff I owned if it was usable.

_________________
Peter Havriluk


Top
 Profile  
 
PostPosted: Mon Jul 10, 2017 2:24 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Mar 06, 2006 10:10 pm
Posts: 2477
Location: Argyle New York
First name: Mike/Mikey/Michael/hey you!
Last Name: Collins
City: Argyle
State: New York
Zip/Postal Code: 12809
Country: U.S.A. /America-yea!!
Focus: Build
Status: Professional
use the flatsawn.
Much more difficult to split then quartered!
Thickness depends on -string tension .& top thickness.
2.5mm-3mm is best !

I'll let ya all think about that for awhile.

Mike

_________________
Mike Collins



These users thanked the author Mike Collins for the post: SteveCourtright (Tue Jul 11, 2017 2:17 pm)
Top
 Profile  
 
PostPosted: Mon Jul 10, 2017 3:13 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sat Jan 15, 2005 12:50 pm
Posts: 3869
Location: United States
The only real problem with flat sawn bridge plates in general is that it's the cut that has the highest tendency to crack. Basically that's because the medullary rays run perpendicular to the surface, and act as weak points in the bond between the cells. Quartered wood gets part of it's stiffness and strength across the grain from the rays, which have cells that run along the radius of the tree, and tie the cells together in that direction.

Probably the best cut for bridge plates is 'skew' or 'rift', where the annual ring lines are at 45 degrees to the surface. This gives the lowest cross grain stiffness, and the highest shear modulus and splitting resistance. The low cross stiffness is actually a good thin in this case, as it allows the bridge plate to deform along with the top as it bellies, helping to avoid a stress riser along the front and back edges of the plate.

The two biggest problems with bridge plates come in when the wear through, and when they crack along the line of the pin holes. Skew cut rock maples is a good choice because it resists both problems. Persimmon is even better.



These users thanked the author Alan Carruth for the post: ChuckH (Sat Jul 15, 2017 11:30 pm)
Top
 Profile  
 
PostPosted: Mon Jul 10, 2017 3:20 pm 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Fri Nov 02, 2007 9:49 am
Posts: 12971
Location: Ann Arbor, Michigan
First name: Hesh
Last Name: Breakstone
City: Ann Arbor
State: Michigan
Country: United States
Status: Professional
I'd use flat sawn too and IIRC when I was building my plates were around .090" thick. Rift is preferable but I think that flat is fine too provided that you don't mimic 70's Martins and make the plate bigger than the guitar....

What's in my view more important if you want the instrument built as well as we know how is to use 3 degree (5 degree is nearly as good) unslotted pins and slot the bridge, top and plate for the strings. This is how it was done back in the day before the advent of cheap-arse, mass produced plastic pins.

The 1870's and later guitars that we work on that had unslotted pins usually have bridge plates that look like new and have no issues requiring repair or replacement. The same is not true of instruments that had slotted pins.

Slotted pins permit the string balls over time to start to migrate upward eating away at the sides of the pin holes in the bridge plate. This leads to bridge plates developing a crease and even a split along the pin holes which leads to lifting bridges, loose braces, top deformation, depressions in front of the bridge and a partridge in a pear tree....;) Sorry I actually speak like this in person.... at times.

Anyway that's my 1.5 cents, use the flat stuff, make it .090" thick or no thicker and obtain and use unslotted pins.

_________________
Ann Arbor Guitars



These users thanked the author Hesh for the post: dpetrzelka (Tue Jul 11, 2017 10:11 am)
Top
 Profile  
 
PostPosted: Mon Jul 10, 2017 5:22 pm 
Offline
Koa
Koa

Joined: Mon Feb 13, 2012 8:49 pm
Posts: 952
First name: peter
Last Name: havriluk
City: granby
State: ct
Zip/Postal Code: 06035
Country: usa
Focus: Build
Status: Amateur
Thanks, everybody. I feel like I started a symposium about bridge plates.

_________________
Peter Havriluk



These users thanked the author phavriluk for the post: Hesh (Tue Jul 11, 2017 4:31 am)
Top
 Profile  
 
PostPosted: Mon Jul 10, 2017 6:00 pm 
Offline
Koa
Koa

Joined: Sat May 19, 2007 11:03 am
Posts: 1737
Location: Litchfield MI
Focus: Build
Status: Professional
I totally agree with Hesh but want to make sure this point does not get over looked


"unslotted pins and slot the bridge, top and plate for the strings."

When done correctly I have found that the strings will stay in place even without pins!

_________________
Ken Cierp

http://www.kennethmichaelguitars.com/



These users thanked the author kencierp for the post (total 2): dpetrzelka (Tue Jul 11, 2017 1:38 pm) • Hesh (Tue Jul 11, 2017 4:31 am)
Top
 Profile  
 
PostPosted: Tue Jul 11, 2017 4:31 am 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Fri Nov 02, 2007 9:49 am
Posts: 12971
Location: Ann Arbor, Michigan
First name: Hesh
Last Name: Breakstone
City: Ann Arbor
State: Michigan
Country: United States
Status: Professional
kencierp wrote:
I totally agree with Hesh but want to make sure this point does not get over looked


"unslotted pins and slot the bridge, top and plate for the strings."

When done correctly I have found that the strings will stay in place even without pins!


Exactly! [:Y:]

_________________
Ann Arbor Guitars


Top
 Profile  
 
PostPosted: Tue Jul 11, 2017 10:37 am 
Offline
Koa
Koa

Joined: Mon Feb 13, 2012 8:49 pm
Posts: 952
First name: peter
Last Name: havriluk
City: granby
State: ct
Zip/Postal Code: 06035
Country: usa
Focus: Build
Status: Amateur
Preaching to the choir!

_________________
Peter Havriluk


Top
 Profile  
 
PostPosted: Tue Jul 11, 2017 1:13 pm 
Offline
Koa
Koa

Joined: Sat May 19, 2007 11:03 am
Posts: 1737
Location: Litchfield MI
Focus: Build
Status: Professional
Quote:
Preaching to the choir!


On the contrary -- Look to see how many modern guitars have this feature instead of slotted pins and rarely have I seen any of the no name hand made's or other factory guitars that even have bridge slots/ramps. Keep in mind that posts are for all forum members including those getting started, not just the OP.

_________________
Ken Cierp

http://www.kennethmichaelguitars.com/


Top
 Profile  
 
PostPosted: Tue Jul 11, 2017 2:35 pm 
Offline
Contributing Member
Contributing Member

Joined: Sun May 19, 2013 10:22 am
Posts: 727
First name: Brian
Last Name: McDonald
City: Okanagan Centre
State: British Columbia
Zip/Postal Code: V4V2H6
Country: Canada
Focus: Build
Status: Amateur
Why is it so hard to find unslotted pins?
Or have I not looked hard enough?

B

_________________
My memory is so good, sometimes I remember things that never happened.


Top
 Profile  
 
PostPosted: Tue Jul 11, 2017 2:39 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3289
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
Bri wrote:
Why is it so hard to find unslotted pins?
Or have I not looked hard enough?

B


I use these: https://www.lmii.com/products/mostly-wo ... nd-plastic

Or just use the slotted ones and flip them around. beehive

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars



These users thanked the author bcombs510 for the post: Hesh (Tue Jul 11, 2017 3:18 pm)
Top
 Profile  
 
PostPosted: Tue Jul 11, 2017 3:25 pm 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Fri Nov 02, 2007 9:49 am
Posts: 12971
Location: Ann Arbor, Michigan
First name: Hesh
Last Name: Breakstone
City: Ann Arbor
State: Michigan
Country: United States
Status: Professional
Bri wrote:
Why is it so hard to find unslotted pins?
Or have I not looked hard enough?

B


Bri they are harder to find and the 3 degree ones are really hard to find but they are out there.

I was fond of using BRW 3 degree unslotted pins and had to have them made for me.... so I did....:)

The problem with using slotted pins and turning them around is if anyone else ever restrings the guitar and puts the slots forward not understanding what you intended the extra large slots will encourage the string balls to migrate upward right away and damage things.

I'll add that since I mentioned BRW pins no... I do not and did not include them with my guitars for sonic reasons. I just liked the look. I also had African Blackwood pins made and used those too again for the look.

If bridge pin material has any sonic impact at all, and it actually likely does.... IMO... it's the change in mass of different pin materials on the sweet spot of a guitar top, the bridge. Long ago in another thread this was Al C's belief about pin material and tone and it's worked for me ever since Al shared it. Thanks again Al!

Some guitars may benefit from more or less mass in the bridge area. How do we know which? We can't without trying them out and wondering if we are imagining what we hear.... [uncle] :D Anyway they look nice..... :D

_________________
Ann Arbor Guitars


Top
 Profile  
 
PostPosted: Tue Jul 11, 2017 3:39 pm 
Offline
Cocobolo
Cocobolo

Joined: Sun Jun 21, 2009 6:14 pm
Posts: 439
First name: Mike
Last Name: Imbler
City: Wichita
State: KS
Zip/Postal Code: 67204
Country: usa
Focus: Build
bcombs510 wrote:
Bri wrote:
Why is it so hard to find unslotted pins?
Or have I not looked hard enough?

B


I use these: https://www.lmii.com/products/mostly-wo ... nd-plastic

Or just use the slotted ones and flip them around. beehive


I hesitate to ask, but that is exactly what I had planned to do. Is there a problem with just putting the pin slot opposite to the string slot?
thanks,


Top
 Profile  
 
PostPosted: Tue Jul 11, 2017 3:56 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3289
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
Imbler wrote:
bcombs510 wrote:
Bri wrote:
Why is it so hard to find unslotted pins?
Or have I not looked hard enough?

B


I use these: https://www.lmii.com/products/mostly-wo ... nd-plastic

Or just use the slotted ones and flip them around. beehive


I hesitate to ask, but that is exactly what I had planned to do. Is there a problem with just putting the pin slot opposite to the string slot?
thanks,


See the response from Hesh above. It will work fine if it's just for you.

LMI has the 3 degree unslotted pins. Make sure your pin reamer matches.


Sent from my iPhone using Tapatalk

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars



These users thanked the author bcombs510 for the post: Imbler (Tue Jul 11, 2017 4:50 pm)
Top
 Profile  
 
PostPosted: Tue Jul 11, 2017 4:00 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Nov 12, 2014 10:02 am
Posts: 513
First name: Daniel
Last Name: Petrzelka
State: Washington
Country: United States
Focus: Build
Does anyone have a link to a discussion that lays out why one would choose 3 degree rather than 5 degree?
I have been using 5, have the reamer and pile of unslotted pins to match.


Top
 Profile  
 
PostPosted: Tue Jul 11, 2017 4:05 pm 
Offline
Koa
Koa

Joined: Mon Jul 11, 2005 5:17 am
Posts: 995
Location: United States
City: Tyler
State: Texas
3 degree has a larger opening. More room for the ball end to get through, normally a non-issue, unless you have a thicker than normal bridge/top/plate sandwiche.



These users thanked the author Glen H for the post: dpetrzelka (Tue Jul 11, 2017 6:08 pm)
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 23 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 60 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com