Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 5:06 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 18 posts ] 
Author Message
PostPosted: Fri Jan 11, 2019 9:46 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Feb 20, 2008 9:12 pm
Posts: 6977
First name: Mike
Last Name: O'Melia
City: Huntsville
State: Alabama
Focus: Build
Status: Semi-pro
I do not know where I went wrong. I had a guitar body that had suffered a lot of damage at the hands of it's owner. They asked me to repair. I should have said no. I removed the neck, sanded to wood. Repaired damage. Seal coated. Z-poxy. Sanded, then wash coat in zpoxy. Looked great. Sprayed with Enduro-Var. after three coats, I level sanded to remove orange peel. Then sprayed a bunch more coats. Let set for a week, level sand. Each time I've done then, I end up with thin layers higher than surrounding area. Like plateaus. Lets just say the surface is not level. Why? Where is that effect coming from? Is my early level sanding causing this? I realize you will want pictures. I will try.


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 9:56 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Feb 20, 2008 9:12 pm
Posts: 6977
First name: Mike
Last Name: O'Melia
City: Huntsville
State: Alabama
Focus: Build
Status: Semi-pro
Here is a pic. You can see areas of shine and dull.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 10:40 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu Feb 09, 2006 2:35 pm
Posts: 2951
Location: United States
First name: Joe
Last Name: Beaver
City: Lake Forest
State: California
Focus: Build
I'm guessing it has to do with the original finish/porefill on the wood. I think I remember you have used the seal/epoxy/Enduro-Var procedure before with success. My only other thought is did you use a different sand paper than before? Water based can be temperamental. Or maybe the owner used a silicone polish on it that somehow survived the sand to bare wood.

So... no real help here

_________________
Joe Beaver
Maker of Sawdust


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 11:39 am 
Offline
Contributing Member
Contributing Member

Joined: Tue Jan 03, 2006 1:47 pm
Posts: 1624
Location: United States
First name: Larry
Last Name: Hawes
Focus: Build
Status: Amateur
Curious Mike, you write "Seal coated. Z-poxy." I have never seal coated under Z-Poxy and not sure why one would/should. What was that seal coat? Why?

Curious is all, as my help and experience is limited but have applied EnduroVaor over ZPoxy over bare wood with no problems other than normal bone head user errors that just sand out.

Keep us updated please.

_________________
Thank You and Best To All


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 12:21 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Feb 20, 2008 9:12 pm
Posts: 6977
First name: Mike
Last Name: O'Melia
City: Huntsville
State: Alabama
Focus: Build
Status: Semi-pro
Sealer is two part, keeps oils from spreading. It is an adhesion promoter as well.


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 12:38 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Feb 20, 2008 9:12 pm
Posts: 6977
First name: Mike
Last Name: O'Melia
City: Huntsville
State: Alabama
Focus: Build
Status: Semi-pro
Joe, I have no idea. I'm tossing Enduro. Going to do this one in nitro and figure out my next step for finishing future bodies.


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 12:40 pm 
Offline
Contributing Member
Contributing Member

Joined: Tue Jan 03, 2006 1:47 pm
Posts: 1624
Location: United States
First name: Larry
Last Name: Hawes
Focus: Build
Status: Amateur
Mike OMelia wrote:
Sealer is two part, keeps oils from spreading. It is an adhesion promoter as well.


Thanks Mike, have you used it on this wood type before? Would you mind sharing a couple details about the 2 part product? Like what it is? Curious for a couple reasons, one there might be others that might want to use it in the future, and second just wondering if this wood type (which is what?) behave a little differently with this 2 part sealer.

And again probably not helping much, but have never heard of using a sealer under Z-Poxy but I have a lot to learn.

_________________
Thank You and Best To All


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 2:15 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Feb 20, 2008 9:12 pm
Posts: 6977
First name: Mike
Last Name: O'Melia
City: Huntsville
State: Alabama
Focus: Build
Status: Semi-pro
http://www.simteccoatings.com/MSDS.ivnu

58x1 and 58x2

Product works fine. One component has a limited shelf life. Spray it on. I have used it before on this wood. No problems


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 2:28 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3288
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
Mike, what grit are you leveling with?

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 2:32 pm 
Offline
Contributing Member
Contributing Member

Joined: Tue Jan 03, 2006 1:47 pm
Posts: 1624
Location: United States
First name: Larry
Last Name: Hawes
Focus: Build
Status: Amateur
Mike OMelia wrote:
http://www.simteccoatings.com/MSDS.ivnu

58x1 and 58x2

Product works fine. One component has a limited shelf life. Spray it on. I have used it before on this wood. No problems


Thanks for taking the time to post the info. One last question...what wood? [:Y:]

_________________
Thank You and Best To All


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 5:16 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Feb 20, 2008 9:12 pm
Posts: 6977
First name: Mike
Last Name: O'Melia
City: Huntsville
State: Alabama
Focus: Build
Status: Semi-pro
cocobolo


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 5:51 pm 
Offline
Contributing Member
Contributing Member

Joined: Tue Jan 03, 2006 1:47 pm
Posts: 1624
Location: United States
First name: Larry
Last Name: Hawes
Focus: Build
Status: Amateur
THX

_________________
Thank You and Best To All


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 6:14 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu Feb 09, 2006 2:35 pm
Posts: 2951
Location: United States
First name: Joe
Last Name: Beaver
City: Lake Forest
State: California
Focus: Build
Mike, I know what you mean. I was a KTM user for many years. When they sold out I decided to go with Cardinal LuthierLac. I like it a lot, but being a nitro it has some drawbacks. I plan to try Royal-lac post-catalyzed on my next build. It is a prototype for a new way of building, at least for me. I did some test panels with the stuff over various pore fills a couple years ago. So far none of the crazing and checking problems others have reported.

I am always looking for the perfect finish. What I really want to try is a two part urethane, Maybe latter this year.

_________________
Joe Beaver
Maker of Sawdust


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 6:51 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Feb 20, 2008 9:12 pm
Posts: 6977
First name: Mike
Last Name: O'Melia
City: Huntsville
State: Alabama
Focus: Build
Status: Semi-pro
What do u mean by two part urethane? Something catalyzed? Me personally, I'm done with water borne products. I think I will research some higher end products. I never had issues with Enduro until recently.


Top
 Profile  
 
PostPosted: Fri Jan 11, 2019 7:12 pm 
Offline
Koa
Koa
User avatar

Joined: Sat Jan 19, 2013 7:33 am
Posts: 1831
First name: Willard
Last Name: Guthrie
City: Cumberland
State: Maryland 21502
Zip/Postal Code: 21502
Country: United State
Focus: Repair
Status: Semi-pro
Could the seal coat be incompatible with Enduro-Var? It looks very similar to a lacquer touch-up where the surface is not prepped for burn-in, so I would suspect adhesion issues where the layers did not tie together. Enduro-Var will chemically bond if recoated within an hour or so, but if not recoated in 2 hours, the surface needs to be sanded.

We don't use Enduro-var over anything but raw wood or 3M Silvertip Fast. I assume you are dry-sanding, as wet sanding even well-cured Enduro-var can result in varying levels of witness lines.

We dumped Z-Poxy for epoxy fill work a few years ago, both because of the bleed issues and downstream separation problems with lacquer topcoats. This may be related to the amine blush issue which Z-Poxy has, and reaction between higher pH salts and lower pH (~ 5.5-6 perspiration. Maas, System 3 Silvertip, and West 105/209 are blush and bloom free. Also, Z-Poxy goes more intensely amber as it ages, so can be a pain to touch up on a sand-through.

_________________
We have become a civilization that elevates idiots, prostitutes, and clowns. Am I still to defend it? Yes, for its principles. Yes, for what it was. Yes, for what it still may be.

-Mark Helprin, The Oceans and the Stars: A Sea Story, A War Story, A Love Story (A Novel)


Top
 Profile  
 
PostPosted: Sat Jan 12, 2019 2:12 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu Feb 09, 2006 2:35 pm
Posts: 2951
Location: United States
First name: Joe
Last Name: Beaver
City: Lake Forest
State: California
Focus: Build
Mike,
The urethane finish I am most interested in trying is Deltron from PPG. It is an automotive finish that Brian Howard used on guitars before he went to the UV cured stuff. I haven't got it figured out yet but, I think he used the DCU2021 urethane and the DCX61 hardener. He did say any pore fill that works with solvent finishes should work fine. You will also need to seal with a vinyl sealer after the fill. He recommended a Mohawk product but I don't know which one.

The pieces I am missing is a paint schedule, along with a sanding and buffing schedule.

_________________
Joe Beaver
Maker of Sawdust



These users thanked the author Joe Beaver for the post: edstrummer (Sat Jan 12, 2019 5:29 am)
Top
 Profile  
 
PostPosted: Sat Jan 12, 2019 7:48 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Dec 27, 2010 9:06 pm
Posts: 2739
Location: Magnolia DE
First name: Brian
Last Name: Howard
City: Magnolia
State: Delaware
Zip/Postal Code: 19962
Country: United States
Focus: Repair
Status: Professional
Yes, PPG DCU2021 Concept clear is a very good choice. This is a complete chemical cured finish and will harden to rubber inside a gun if not cleaned fairly promptly . Also requires accurate chemistry for mixing.

_________________
Brian

You never know what you are capable of until you actually try.

https://www.howardguitarsdelaware.com/


Top
 Profile  
 
PostPosted: Sat Jan 12, 2019 2:44 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu Feb 09, 2006 2:35 pm
Posts: 2951
Location: United States
First name: Joe
Last Name: Beaver
City: Lake Forest
State: California
Focus: Build
Brian,
Hardening inside the gun is one of my concerns. How many coats, and time between coats are you able to spray before the leftover product has to be dumped and the equipment cleaned?

_________________
Joe Beaver
Maker of Sawdust


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 18 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 41 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com