Official Luthiers Forum! • View topic

Board index » Fixture, Video and Picture Tutorials

All times are UTC - 5 hours

Go-bar material

Page 1 of 1

[ 12 posts ]

Print view

Previous topic | Next topic

Author

Message

Doug Balzer

Post subject: Go-bar material

Posted: Mon Jan 14, 2013 10:53 pm

Contributing Member

Joined: Sun Dec 30, 2012 10:04 pm
Posts: 712
First name: Doug
Last Name: Balzer
City: Calgary
State: Alberta
Country: Canada
Focus: Build
Status: Semi-pro

So what type of wood works well for go-bars?

_________________
Doug

Don't let fear or common sense stop you from trying to build something

Top

wtholmwood

Post subject: Re: Go-bar material

Posted: Tue Jan 15, 2013 4:15 am

Contributing Member

Joined: Sun Oct 28, 2012 2:04 am
Posts: 92
First name: William
Last Name: Holmwood
City: Brighton
Country: England
Focus: Build

I have very little experience but a friend of mine uses mahogany. Says it works really well.

Top

Dan Pennington

Post subject: Re: Go-bar material

Posted: Tue Jan 15, 2013 5:05 am

Contributing Member

Joined: Fri Nov 13, 2009 8:56 am
Posts: 388
Location: Minneapolis
First name: Dan
Last Name: Pennington
City: Brooklyn Park
State: MN
Zip/Postal Code: 55428
Country: United States
Focus: Build
Status: Semi-pro

I use 1/4 in. slices of 3/4 boards left over from my banjo rim making. So, I wind up with an assortment of woods - maple, birch, cherry, walnut, mahogany, and some pine. Cheap and disposable when they get too short.

Top

Tobes

Post subject: Re: Go-bar material

Posted: Tue Jan 15, 2013 12:14 pm

Walnut

Joined: Sun Dec 30, 2012 12:54 pm
Posts: 9
First name: Alan
Last Name: Tobler
City: Tucson
State: Arizona
Zip/Postal Code: 85748
Country: USA
Focus: Build
Status: Semi-pro

I use whatever scrap is laying around. Most of my sticks are alder. I cut them to 5/16 x 3/4. I tried 1/4 x 1/4 but a lot of them snapped.

_________________
The dullest pencil is sharper than the keenest mind.

Top

ZekeM

Post subject: Re: Go-bar material

Posted: Mon Jan 21, 2013 4:57 pm

Contributing Member

Joined: Fri Dec 21, 2012 11:52 am
Posts: 1388
First name: Zeke
Last Name: McKee
City: Goodlettsville
State: TN
Zip/Postal Code: 37070
Country: United States
Focus: Build
Status: Amateur

Mine are pine from chopped up 2x4s. its cheap so i dont feel bad when i throw a fit and break some. laughing6-hehe

Top

Link Van Cleave

Post subject: Re: Go-bar material

Posted: Sat Jan 26, 2013 12:30 pm

Contributing Member

Joined: Wed Mar 19, 2008 11:49 am
Posts: 897
Location: Northen Cal.

Ash, Oak, Osage Orange, Hickory, Tan Oak, Elm. If air dried and rived they will never break, split, shatter , etc.
L.

_________________
Cut to size.....Beat to fit.....Paint to match.

Top

joshnothing

Post subject: Re: Go-bar material

Posted: Tue Jan 29, 2013 10:14 pm

Koa

Joined: Tue Jan 15, 2013 10:00 pm
Posts: 980
First name: Josh
Focus: Build
Status: Amateur

Bamboo garden stakes, $5 for a bag of 50. I wrap a bit of cloth tape around the end to stop them sliding.

Top

Bryan Bear

Post subject: Re: Go-bar material

Posted: Sat Feb 02, 2013 9:42 pm

Brazilian Rosewood

Joined: Thu Feb 12, 2009 12:12 pm
Posts: 3291
First name: Bryan
Last Name: Bear
City: St. Louis
State: Mo
Country: USA
Focus: Build
Status: Amateur

I was just thinking about bamboo stakes for this the other day. I'll have to remember to get a bag.

_________________
Bryan Bear PMoMC

Take care of your feet, and your feet will take care of you.

Top

RusRob

Post subject: Re: Go-bar material

Posted: Thu Mar 28, 2013 9:54 pm

Contributing Member

Joined: Tue Mar 19, 2013 3:34 pm
Posts: 1097
First name: Bob
Last Name: Russell
State: Michigan USA
Focus: Repair
Status: Semi-pro

I am using 1/4" fiberglass rod from Granger Supply. It comes in 10 foot lengths and is pretty inexpensive. I started using wood strips but found each piece had a different compression which would make other bars already in place pop out. I don't have that problem since I started using fiberglass.

It only cost $6 for a 10 foot length so it is cheap. The only issue is it is not coated but a coat of bin sealer took care of that. I then dipped each end into that rubber you coat tool handles in and they are just like real Go-Bars.

Here is a link:

http://www.grainger.com/Grainger/wwg/search.shtml?searchQuery=fiberglass+rod&op=search&Ntt=fiberglass+rod&N=0&GlobalSearch=true&sst=subset

Top

FishtownMike

Post subject: Re: Go-bar material

Posted: Sun Mar 31, 2013 1:07 am

Koa

Joined: Sat Aug 04, 2007 10:37 am
Posts: 590
Location: United States
First name: Michael
Last Name: Shaw
City: Phila
State: PA
Zip/Postal Code: 19125
Country: United States

I use these 3/16" fiberglass rods I bought years ago from a kite supply site that someone on here recommended. The 3/16" rods work fine. I thhought the 1/4" one sold at home centers for driveway markng and such were to stiff.....Mike
http://www.intothewind.com/sessions/3b2 ... 60f/search

_________________
Guitars, guitars and more guitars.

Top

weslewis

Post subject: Re: Go-bar material

Posted: Mon Jun 17, 2013 7:38 am

Contributing Member

Joined: Sun Jan 10, 2010 11:40 am
Posts: 764
First name: wes
Last Name: Lewis
City: Garland
State: Tx.
Zip/Postal Code: 75044
Focus: Build

http://www.harborfreight.com/3-16-inch- ... 65326.html

_________________
MK5acoustics.com

Top

Page 1 of 1

[ 12 posts ]

Board index » Fixture, Video and Picture Tutorials

All times are UTC - 5 hours

Who is online

Users browsing this forum: No registered users and 8 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: