Thanks for the tip.
![[:Y:]](./images/smilies/smiley20.gif "Thumbs Up")
| Official Luthiers Forum! http://luthiersforum.com/forum/ |
|
| Burnisher idea. http://luthiersforum.com/forum/viewtopic.php?f=10117&t=39517 |
Page 1 of 1 |
| Author: | WilbPorter [ Tue Feb 26, 2013 8:11 pm ] |
| Post subject: | Burnisher idea. |
Sent from my GT-P3113 using Tapatalk 2 |
|
| Author: | WilbPorter [ Tue Feb 26, 2013 8:13 pm ] |
| Post subject: | Re: Burnisher idea. |
Here's a link to a burnisher idea from a friend of mine. https://www.youtube.com/watch?v=-EnhuGN ... ata_player Sent from my GT-P3113 using Tapatalk 2 |
|
| Author: | mzimbel [ Wed Feb 27, 2013 10:21 pm ] |
| Post subject: | Re: Burnisher idea. |
Thanks for the tip.
|
|
| Author: | bluzdawg [ Thu Feb 28, 2013 9:26 am ] |
| Post subject: | Re: Burnisher idea. |
That's a great idea. What did he call that, an iteration bearing? |
|
| Author: | WilbPorter [ Fri Mar 01, 2013 1:21 pm ] |
| Post subject: | Re: Burnisher idea. |
Actually it's the inner part ( I think he called it 'race') of a snowmobile bearing. Any bearing should do, roller type that is. He smashed the outer part to break the bearing apart, but an angle grinder could quickly separate the two parts. Bet your friendly auto fixer has lots of used bearings. Sent from my GT-P3113 using Tapatalk 2 |
|
| Author: | Dkeddy27 [ Fri Mar 01, 2013 7:03 pm ] |
| Post subject: | Re: Burnisher idea. |
Great idea! Both sides at the same time, I like it!! I might grind that shape in an old drills shaft. |
|
| Author: | FishtownMike [ Sun Mar 31, 2013 2:03 am ] |
| Post subject: | Re: Burnisher idea. |
Looks like an accident waiting to happen. A better idea would be to clamp the bearing in the vise...Mike |
|
| Author: | Fred Tellier [ Sun Mar 31, 2013 8:19 am ] |
| Post subject: | Re: Burnisher idea. |
+ 1 on the clamp in vice for safety. Any ball bearing would do but a large one would be easier to clamp in the vice. Fred |
|
| Author: | Daniel Minard [ Wed Jun 05, 2013 1:14 pm ] |
| Post subject: | Re: Burnisher idea. |
What Fred said... Ball bearing, not roller bearing. Cool idea! |
|
| Author: | npalen [ Wed Jun 05, 2013 8:39 pm ] |
| Post subject: | Re: Burnisher idea. |
Looks like the cross section radius of the ball path would effect the shape of the burr by taking it a little past 90 degrees to the scrapers edge. Also, the diameter of the bearing might influence how hard the scraper must be pressed against the bearing. Just thinking about what's happening during the process--not trying to complicate it. Great idea! |
|
| Author: | WilbPorter [ Mon Jun 17, 2013 4:30 am ] |
| Post subject: | Re: Burnisher idea. |
Yeah, I meant ball bearing, not roller bearing. Sent from my GT-P3113 using Tapatalk 4 Beta |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|