Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 6:01 am


All times are UTC - 5 hours


Forum rules


Same rules apply to all forums at the Luthiers Forum.




Post new topic Reply to topic  [ 18 posts ] 
Author Message
PostPosted: Tue Sep 09, 2014 12:14 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Aug 23, 2010 11:42 pm
Posts: 1701
First name: John
Last Name: Parchem
City: Seattle
State: Wa
Zip/Postal Code: 98177
Country: USA
Focus: Build
Status: Amateur
I am making a couple of tenor ukuleles. The Martin GAL plans I have are for a 12 fret body join but I plan to build to a 14 fret body join. The plan has a 17" scale which I will leave alone so I will move the bridge toward the sound hole. I am going to use the plans 3 brace fan. My other thought was to move the 2 outer tone bars out a bit so they would pass under the bridge the same as shown in the 12 fret GAL plans I have.

Am I on the correct path in moving forward with this?

Thanks

_________________
http://www.Harvestmoonguitars.com


Top
 Profile  
 
PostPosted: Tue Sep 09, 2014 8:04 pm 
Offline
Koa
Koa

Joined: Sat Nov 07, 2009 9:34 pm
Posts: 552
City: winnipeg
State: manitoba
Country: canada
Focus: Build
Status: Amateur
This may be a dumb question but have redesigned the neck yet?
The Hana Lima plan calls for the outside tone-bars to be tight to the ends of the bridge-patch and the center tone-bar to jump over the bridge-patch (snuggly). I tend to jump over the bridge-patch, more from habit than for any reason.
Remember, the bridge is the last piece to be glued in place, measure it EXACTLY.

Good luck

Bob :ugeek:


Top
 Profile  
 
PostPosted: Tue Sep 09, 2014 8:17 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Aug 23, 2010 11:42 pm
Posts: 1701
First name: John
Last Name: Parchem
City: Seattle
State: Wa
Zip/Postal Code: 98177
Country: USA
Focus: Build
Status: Amateur
Thanks Bob, I do have a layout for a 14 fret to the body neck. I plan to glue on the bridge after the guitar is assembled and finished, like I do my guitars. I will place the bridge patch correctly and use it to help place the outside tone bars.

_________________
http://www.Harvestmoonguitars.com


Top
 Profile  
 
PostPosted: Wed Sep 10, 2014 11:28 pm 
Offline
Mahogany
Mahogany

Joined: Mon Dec 22, 2008 7:22 pm
Posts: 88
First name: doug
Last Name: powdrell
City: hilo
State: big island
Focus: Build
Status: Amateur
John-you are on the right path....been there...12 to 14 fret, adjust fans to bridge wings, soundhole, f.b. extension....minor adjustments. I find 14 fret fuller sound as more balanced placement of bridge at lower bout....have fun!!! Doug


Top
 Profile  
 
PostPosted: Sat Sep 13, 2014 9:01 pm 
Offline
Koa
Koa

Joined: Sat May 17, 2014 12:45 pm
Posts: 644
First name: Lonnie
Last Name: Barber
City: Manchester
State: Tennessee
Zip/Postal Code: 37355
Country: United States
Focus: Build
Status: Amateur
I took a page from Bogdonovichs book. Took an old Uke I had and made a stick that fits exactly between the nut and saddle. It gives me the exact measurements for the frets as well as the scale length. Not really much room for error using it. I just drilled a hole in it covered it with a couple coats of shellac and hung it on the wall where it awaits the next use. Just a thought.


Sent from my iPhone using Tapatalk


Top
 Profile  
 
PostPosted: Sun Sep 14, 2014 11:38 am 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Tue Nov 14, 2006 4:10 am
Posts: 151
Location: United States
First name: Kevin
Last Name: Mason
City: Wheeling
State: IL
Zip/Postal Code: 60090
Country: USA
Focus: Build
Status: Semi-pro
Yes, what you describe is what I do. Bridge closer to the Soundhole and adjust the outside braces so that the wings of the bridge are coupled with those braces.

_________________
Kevin Mason
Mason Guitars and Ukuleles on Facebook
http://masonguitars.net


Top
 Profile  
 
PostPosted: Sun Sep 14, 2014 11:40 am 
Offline
Koa
Koa

Joined: Sat Nov 07, 2009 9:34 pm
Posts: 552
City: winnipeg
State: manitoba
Country: canada
Focus: Build
Status: Amateur
I use the Stewmac fret calculator and work in millimeters. I have found that if I am correct to half a millimeter (20 thou), I am accurate enough.

Bob :ugeek:



These users thanked the author unkabob for the post: Lonnie J Barber (Thu Sep 18, 2014 2:08 pm)
Top
 Profile  
 
PostPosted: Thu Sep 18, 2014 2:09 pm 
Offline
Koa
Koa

Joined: Sat May 17, 2014 12:45 pm
Posts: 644
First name: Lonnie
Last Name: Barber
City: Manchester
State: Tennessee
Zip/Postal Code: 37355
Country: United States
Focus: Build
Status: Amateur
I feel the same about the mm's but use the stick for expediency. Very accurate as well as long as your carefull making it.


Sent from my iPhone using Tapatalk


Top
 Profile  
 
PostPosted: Sun Mar 15, 2015 4:12 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Tue Nov 29, 2005 11:44 am
Posts: 2186
Location: Newark, DE
First name: Jim
Last Name: Kirby
Focus: Build
Status: Amateur
Speaking of bridge patches ...

Are they needed? I'm used to building classical guitars and I don't tend to use them.

I'm building my first two ukes right now - both tenors, the second one for a client and the first to investigate just how badly I'm doing it before I do the second one for the client. I don't immediately need a bridge patch as reinforcement
for bridge pins as I'm going to use bridges with tie blocks like a classical. Is there anything important about the bridge patch to the sound? I look and look at the plans and everything seems so over-braced.

I'm doing sort of the opposite of John - starting with the Hana Lima 14 fret plan and doing the 12 fret version. All fretted guitar-like things should have 12 frets to the body, no?? Oh well. :^)

_________________
Jim Kirby
kirby@udel.edu


Top
 Profile  
 
PostPosted: Sun Mar 15, 2015 5:57 pm 
Offline
Koa
Koa

Joined: Sat Apr 19, 2008 10:08 pm
Posts: 1958
Location: Missouri
First name: Patrick
Last Name: Hanna
State: Missouri
Country: USA
John, I did something similar with a mandolin (still under construction). I don't think you'll have any trouble at all moving braces, bridge, etc. I ran into a little situation with mine, because I re-used a mold made for a twelve fret mandolin with a cutaway. When I extended the neck to 14 frets, this necessarily changed the side taper of my neck slightly. In my case, it's okay. My mando is for me, and the difference in taper is very slight. The difference in string spacing is very slight--especially away from the body. With the cutaway, I was locked in to the neck width where it met the body. Without a cutaway mold, this wouldn't have been an issue at all. You will want to keep that in mind as you plan your neck taper.


Top
 Profile  
 
PostPosted: Mon Mar 16, 2015 3:09 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Fri Dec 01, 2006 6:44 pm
Posts: 471
Location: Australia
First name: Allen
Last Name: McFarlen
City: Mt. Sheridan
State: Qld.
Zip/Postal Code: 4868
Country: Australia
Focus: Build
Status: Professional
If you use string through bridges, then you had better use a bridge patch. If a tie block bridge, then depending on how it's braced, then you could go without it.

Many plans call for a bridge patch that is overkill when paired up with the fan braces. Especially in tenors. However, if what you are building doesn't have fan braces, like most concerts and virtually all sopranos, then a bridge patch is absolutely necessary.

_________________
Allen R. McFarlen
Barron River Guitars & Ukuleles
Facebook
Cairns, Australia



These users thanked the author Allen McFarlen for the post: Jim Kirby (Tue Mar 17, 2015 1:59 pm)
Top
 Profile  
 
PostPosted: Tue Mar 17, 2015 2:00 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Tue Nov 29, 2005 11:44 am
Posts: 2186
Location: Newark, DE
First name: Jim
Last Name: Kirby
Focus: Build
Status: Amateur
Allen McFarlen wrote:
If you use string through bridges, then you had better use a bridge patch. If a tie block bridge, then depending on how it's braced, then you could go without it.

Many plans call for a bridge patch that is overkill when paired up with the fan braces. Especially in tenors. However, if what you are building doesn't have fan braces, like most concerts and virtually all sopranos, then a bridge patch is absolutely necessary.


Using fan bracing. I think I'll forgo the patch.

_________________
Jim Kirby
kirby@udel.edu


Top
 Profile  
 
PostPosted: Tue Mar 17, 2015 2:04 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Aug 23, 2010 11:42 pm
Posts: 1701
First name: John
Last Name: Parchem
City: Seattle
State: Wa
Zip/Postal Code: 98177
Country: USA
Focus: Build
Status: Amateur
I built two ukuleles together one with and one without. They both worked out well. They both had tie on bridges.

_________________
http://www.Harvestmoonguitars.com


Top
 Profile  
 
PostPosted: Tue Mar 17, 2015 6:10 pm 
Offline
Cocobolo
Cocobolo

Joined: Wed Dec 29, 2004 1:33 pm
Posts: 270
Location: United States
First name: Dennis
Last Name: Ecklund
City: Athens
State: AL
Zip/Postal Code: 35611
Country: USA
Focus: Build
Status: Amateur
It's worth noting that David (Kawika) Hurd used very thin carbon fiber bridge plates on all of his ukuleles. The idea was to reduce or prevent top cracks by more evenly distributing string tension across the top and to counteract shrinking/expanding stress in the wood. I don't remember for certain, but I think he exclusively used tie-on bridges.


Top
 Profile  
 
PostPosted: Thu Mar 19, 2015 10:32 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Feb 12, 2009 12:12 pm
Posts: 3290
First name: Bryan
Last Name: Bear
City: St. Louis
State: Mo
Country: USA
Focus: Build
Status: Amateur
johnparchem wrote:
I built two ukuleles together one with and one without. They both worked out well. They both had tie on bridges.


Did you notice any obvious differences in tone or volume?

_________________
Bryan Bear PMoMC

Take care of your feet, and your feet will take care of you.


Top
 Profile  
 
PostPosted: Thu Mar 19, 2015 12:32 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Aug 23, 2010 11:42 pm
Posts: 1701
First name: John
Last Name: Parchem
City: Seattle
State: Wa
Zip/Postal Code: 98177
Country: USA
Focus: Build
Status: Amateur
Bryan Bear wrote:
johnparchem wrote:
I built two ukuleles together one with and one without. They both worked out well. They both had tie on bridges.


Did you notice any obvious differences in tone or volume?


I can not really say as there were other changes, different top and back and side wood: adi\bearclaw sitka, Koa\Rosewood. So I could not really tell anything obvious with that change.

_________________
http://www.Harvestmoonguitars.com



These users thanked the author johnparchem for the post: Bryan Bear (Fri Mar 20, 2015 11:18 pm)
Top
 Profile  
 
PostPosted: Sat Mar 21, 2015 8:51 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Jan 06, 2011 6:08 pm
Posts: 2712
First name: ernest
Last Name: kleinman
City: lee's summit
State: mo
Zip/Postal Code: 64081
Country: usa
Focus: Build
Status: Professional
I always use a thin mahog or spruce patch , whether it/s a pin or Cl style bridge . Cheap insurance. Bridges on ukes do come flying off.Don/t kid yourself there is a lot of tension on ukes depending on scale length .bracing top thickness ,bridge hickness, bridge patch, . FB, etc. My favorite for a balanced sound is a walnut bridge. Have built abt 25 ukes


Top
 Profile  
 
PostPosted: Thu Mar 26, 2015 10:57 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Tue Nov 29, 2005 11:44 am
Posts: 2186
Location: Newark, DE
First name: Jim
Last Name: Kirby
Focus: Build
Status: Amateur
Why would a bridge patch on the inside affect the tendency for a bridge to pull off the outside (assuming a tie-block classical-style bridge.)?

_________________
Jim Kirby
kirby@udel.edu


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 18 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 7 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com