Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 6:17 pm


All times are UTC - 5 hours


Forum rules


Same rules apply to all forums at the Luthiers Forum.




Post new topic Reply to topic  [ 12 posts ] 
Author Message
 Post subject: More tenor uke questions
PostPosted: Mon Feb 23, 2015 5:23 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Tue Nov 29, 2005 11:44 am
Posts: 2186
Location: Newark, DE
First name: Jim
Last Name: Kirby
Focus: Build
Status: Amateur
Thanks for all the help so far.

Rather than bury the next question in an unrelated topic on bracing, I thought I should start anew.

What are your preferred measurements for string clearance at the 12th fret, and string height above the soundboard at the saddle?

_________________
Jim Kirby
kirby@udel.edu


Top
 Profile  
 
PostPosted: Tue Feb 24, 2015 1:10 am 
Offline
Cocobolo
Cocobolo

Joined: Mon Apr 14, 2008 3:20 am
Posts: 376
Location: Kapolei HI
First name: Aaron
Focus: Build
Status: Semi-pro
.100 over the 12th, lower with high tension strings, maybe.

Fretboard is around .200, bridge around .250.

The measurement from soundboard to strings is not one I've taken, but you can do the math from the above measurements once you get the height at the nut.

And I say "around" because depending on my milling, it may be a little less on the fretboard, especially if its inlayed and I sand down a bit (usually a non-issue).

My pickups are about .050 undersaddle, and I go by the 50/50 rule AFTER the pickup is installed. No pickup means more inside the saddle slot than out.

Sorry I don't have a better answer for you.


Top
 Profile  
 
PostPosted: Tue Feb 24, 2015 2:44 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Fri Dec 01, 2006 6:44 pm
Posts: 471
Location: Australia
First name: Allen
Last Name: McFarlen
City: Mt. Sheridan
State: Qld.
Zip/Postal Code: 4868
Country: Australia
Focus: Build
Status: Professional
All my ukes are set up with low action.

I go with 2.2mm clearance at the 12th fret and 9.5 - 10.5 mm at the saddle.

_________________
Allen R. McFarlen
Barron River Guitars & Ukuleles
Facebook
Cairns, Australia


Top
 Profile  
 
PostPosted: Wed Feb 25, 2015 3:19 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Feb 12, 2009 12:12 pm
Posts: 3290
First name: Bryan
Last Name: Bear
City: St. Louis
State: Mo
Country: USA
Focus: Build
Status: Amateur
Jim, forgive me for intruding on your thread but I'd like to ask a related question. I have only made 1 tenor uke and it was my first nylon strung instrument. I used a zero fret and the uke players feedback I got was that the action at the nut was too high. I didn't even know too high was possible. I have another one in the not too distant future. What action at the nut are you guys using? How high above fret 1. . .

_________________
Bryan Bear PMoMC

Take care of your feet, and your feet will take care of you.


Top
 Profile  
 
PostPosted: Wed Feb 25, 2015 8:45 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Feb 25, 2013 4:34 pm
Posts: 223
First name: Kent
Last Name: Wilkinson
City: New Carlisle
State: Ohio
Zip/Postal Code: 45344
Country: USA
Focus: Build
I set mine .015 to .020 at the first.



These users thanked the author Kent Wilkinson for the post: Bryan Bear (Thu Feb 26, 2015 10:26 am)
Top
 Profile  
 
PostPosted: Wed Feb 25, 2015 11:34 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sat Jan 31, 2009 8:50 pm
Posts: 2246
Location: Seattle WA
Focus: Build
Status: Semi-pro
1.5-2mm @12

_________________
Pat


Top
 Profile  
 
PostPosted: Fri Feb 27, 2015 11:09 am 
Offline
Koa
Koa
User avatar

Joined: Thu Dec 18, 2008 11:42 am
Posts: 1135
Location: Hudson, MA
First name: Kevin
Last Name: Quine
City: Hudson
State: MA
Country: Usa
Focus: Build
Status: Amateur
I set up my ukes with 0.01" at the 1st fret and 0.09" at the 12th. 12th fret action can depend on the player....0.1" for heavy strummers and 0.08" for light players. The 1st fret is more critical....it sets the whole "feel" of the instrument


Top
 Profile  
 
PostPosted: Sun Mar 01, 2015 8:56 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Tue Nov 29, 2005 11:44 am
Posts: 2186
Location: Newark, DE
First name: Jim
Last Name: Kirby
Focus: Build
Status: Amateur
Thanks for all the input.

Bryan - your question confused me - how do you get too high an action at the nut end using a zero fret? Seems to me the neck angle would have to be out of whack for such a thing to happen. (Or is the zero fret not crowned to the same height as the regular frets?)

_________________
Jim Kirby
kirby@udel.edu


Top
 Profile  
 
PostPosted: Sun Mar 01, 2015 9:13 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Feb 12, 2009 12:12 pm
Posts: 3290
First name: Bryan
Last Name: Bear
City: St. Louis
State: Mo
Country: USA
Focus: Build
Status: Amateur
Sorry for the confusion Jim, I meant to say that the feed am I got from uke players was that the action was too low. I've never before heard anyone want anything but the lowest possible action up there. I'm not sure if this applies to ukes only or other nylon stringed instruments. Or, maybe it was just the small sample size. It is hard to raise first fret action with a zero fret too. . .

_________________
Bryan Bear PMoMC

Take care of your feet, and your feet will take care of you.


Top
 Profile  
 
PostPosted: Mon Mar 09, 2015 4:03 pm 
Offline
Koa
Koa

Joined: Sat Nov 07, 2009 9:34 pm
Posts: 552
City: winnipeg
State: manitoba
Country: canada
Focus: Build
Status: Amateur
I had a buzz with zero fret so I replaced the zero fret with taller fret wire, problem solved.

Bob :ugeek:


Top
 Profile  
 
PostPosted: Tue Mar 10, 2015 9:25 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Feb 12, 2009 12:12 pm
Posts: 3290
First name: Bryan
Last Name: Bear
City: St. Louis
State: Mo
Country: USA
Focus: Build
Status: Amateur
unkabob wrote:
I had a buzz with zero fret so I replaced the zero fret with taller fret wire, problem solved.

Bob :ugeek:


That is what I ended up doing. I put in a guitar fret. I wouldn't do that on a new build though, using a taller fret pretty much negates the whole point of using a zero fret. Using and actual nut would allow me to sneak up on the preferred nut action whatever that is. . .

_________________
Bryan Bear PMoMC

Take care of your feet, and your feet will take care of you.


Top
 Profile  
 
PostPosted: Sat Apr 11, 2015 3:02 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Tue Nov 29, 2005 11:44 am
Posts: 2186
Location: Newark, DE
First name: Jim
Last Name: Kirby
Focus: Build
Status: Amateur
Thanks to everyone who has provided help so far. I found some time to get back to it this week. Backs are braced (15' radius), tops getting braced now (flat), fretboards slotted today, neck heels rough-carved.

Today's question - what do you think the target bridge weight should be? (Tenor, no bridge patch, tie block rather than pins). I'm formulating ideas about the bridge design, but I'm not sure what the target should be.

_________________
Jim Kirby
kirby@udel.edu


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 12 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 12 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com