Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 12:27 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 6 posts ] 
Author Message
PostPosted: Wed Feb 19, 2014 3:56 pm 
Offline
Mahogany
Mahogany
User avatar

Joined: Tue Feb 04, 2014 10:49 am
Posts: 60
First name: sean
State: nm
Zip/Postal Code: 88349
Country: us
Focus: Build
Status: Amateur
I have repaired and glued up a few neck joints that were broke loose. Right now I find myself needing to pull a neck off an archtop silvertone from the late 50's that is still solid at the joint.

I have heard of pulling a fret, drilling a small hole, and steaming. Unfortunately, I have never seen it and I am not even sure where to start.

_________________
Whatever you do DON'T confuse me as an EXPERT, or MASTER, just a self learned trial and error guy. I had to build a dozen guitar before I found out what a "Luthier" even was (????)


Top
 Profile  
 
PostPosted: Wed Feb 19, 2014 5:24 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5743
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
Works great if you can cobble up some gear.
I used to have the needle to air up a basketball, some rubber tubing, and a tea pot.
I would think these days you could use one of those little hand-held Shark steam cleaners.
Just modify it a bit, and you're in business!

I also used a large hypodermic needle (veterinarian supply) full of boiling water and a drop of liquid soap.
You'll have to be careful, and clean up the mess as you go.

Be prepared to touch up the finish afterwards, either way you choose to go.

_________________
"Act your age, not your shoe size" - Prince


Top
 Profile  
 
PostPosted: Thu Feb 20, 2014 8:04 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Dec 27, 2010 9:06 pm
Posts: 2739
Location: Magnolia DE
First name: Brian
Last Name: Howard
City: Magnolia
State: Delaware
Zip/Postal Code: 19962
Country: United States
Focus: Repair
Status: Professional
If the archtop has a floating fret board you need to pull the heel cap and drill into the joint from there.

_________________
Brian

You never know what you are capable of until you actually try.

https://www.howardguitarsdelaware.com/


Top
 Profile  
 
PostPosted: Thu Feb 20, 2014 9:52 am 
Offline
Mahogany
Mahogany
User avatar

Joined: Tue Feb 04, 2014 10:49 am
Posts: 60
First name: sean
State: nm
Zip/Postal Code: 88349
Country: us
Focus: Build
Status: Amateur
Thanks for the replys, I will give it a shot, and if I run into problems I will be back here begging for help.

_________________
Whatever you do DON'T confuse me as an EXPERT, or MASTER, just a self learned trial and error guy. I had to build a dozen guitar before I found out what a "Luthier" even was (????)


Top
 Profile  
 
PostPosted: Fri Mar 28, 2014 12:11 pm 
Offline
Walnut
Walnut

Joined: Fri Mar 28, 2014 12:02 pm
Posts: 2
First name: Hamilton
Last Name: Perkins
City: Newport Beach
State: CA
Zip/Postal Code: 92663
Country: usa
Focus: Build
Status: Professional
Chris Pile wrote:
Works great if you can cobble up some gear.
I used to have the needle to air up a basketball, some rubber tubing, and a tea pot.
I would think these days you could use one of those little hand-held Shark steam cleaners.
Just modify it a bit, and you're in business!

I also used a large hypodermic needle (veterinarian supply) full of boiling water and a drop of liquid soap.
You'll have to be careful, and clean up the mess as you go.

Be prepared to touch up the finish afterwards, either way you choose to go.



I use a very similar setup. This is the best way to do it. Just keep in mind, the more steam exposure to the glue the better its going to come apart.


Top
 Profile  
 
PostPosted: Sun Mar 30, 2014 5:06 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Thu Oct 04, 2012 3:50 pm
Posts: 294
Location: Austria
First name: Michiyuki
Last Name: Kubo
State:
Country: Österreich
Status: Amateur
To add in, I saw a small device specifically designed to steam hats and coats. It was about 30-40€ and may be worth looking into if you do not have a steam producer already.

_________________
久保
美智え


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 12 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com