Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 8:19 am


All times are UTC - 5 hours





Post new topic Reply to topic  [ 12 posts ] 
Author Message
PostPosted: Sat Jan 16, 2010 7:43 am 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Fri Nov 02, 2007 9:49 am
Posts: 12971
Location: Ann Arbor, Michigan
First name: Hesh
Last Name: Breakstone
City: Ann Arbor
State: Michigan
Country: United States
Status: Professional
Here is how I fit/floss my bridges to my guitar tops.

Set-up includes taping some 120 grit sandpaper to the guitar top with a low tack tape. Since we want the bridge to fit this top precisely and tops are not always the exact radius that we make them to be in the dish it's important to fit the bridge to the location on the top where it will be glued. As such I use tape markers to indicate on the sides of the guitar where I want to be flossing the bridge on the sand paper.

In addition it's difficult, at least for me, to always hang onto something as small as a bridge and not end up sanding my finger tips. So I use latex gloves to get a better purchase on the bridge. Of course if you are known to have any allergies to latex this is not for you....

Attachment:
DSC00732.JPG


The next step is to make pencil lines on the bottom of the bridge so that we may observe our sanding/flossing progress. Be sure to make lines near the corners of the wings in as much as this is the area that will take the longest to floss if your bridge is made with a flat bottom.

Attachment:
DSC00733.JPG


My bridges are made with a radius so in my case the wings of the bridge will sand first if the radius of the bridge is greater than the radius of this particular guitar top.

Attachment:
DSC00734.JPG


Attachment:
DSC00735.JPG


Attachment:
DSC00736.JPG


After a bit of time and flossing the bridge fits the top perfectly with all edges making wood-to-wood contact.

Attachment:
DSCN2676.jpg


Additional considerations:

1) A light scraping of the bottom of the bridge and the guitar top where the bridge will be glued just prior to gluing is advisable for a better joint.

2) Both fitting/flossing the bridge and gluing the bridge benefit from being done in a specific humidity range since the guitar top will react to changes in humidity. If you flossed the bridge to fit with the humidity in the area of 45% glue the bridge on in that range too and the great fit that you had prior when fitting will be there for you.

Thanks!


You do not have the required permissions to view the files attached to this post.

_________________
Ann Arbor Guitars


Top
 Profile  
 
PostPosted: Sat Jan 16, 2010 12:16 pm 
Offline
Mahogany
Mahogany

Joined: Thu Dec 31, 2009 2:37 pm
Posts: 77
First name: mark
Last Name: warwick
Zip/Postal Code: ll57 4RE
Country: Uk
Focus: Build
Status: Amateur
Thanks for that Hesh!

Curious though... How come it is taking material off the outside of the bridge if the top has a radius?

_________________
Disappointment is an empty box full of expectation


Top
 Profile  
 
PostPosted: Sat Jan 16, 2010 5:07 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Fri Apr 13, 2007 12:52 am
Posts: 285
Location: Canada
First name: Cal
Last Name: Maier
City: Crossfield
State: AB
Country: Canada
Focus: Build
Status: Professional
[/quote]How come it is taking material off the outside of the bridge if the top has a radius?
Quote:

Quote:
My bridges are made with a radius so in my case the wings of the bridge will sand first if the radius of the bridge is greater than the radius of this particular guitar top.


That's why.

Cal

_________________
Remember, there are no stupid questions, only stupid answers!


Top
 Profile  
 
PostPosted: Sun Jan 17, 2010 4:24 am 
Offline
Mahogany
Mahogany

Joined: Thu Dec 31, 2009 2:37 pm
Posts: 77
First name: mark
Last Name: warwick
Zip/Postal Code: ll57 4RE
Country: Uk
Focus: Build
Status: Amateur
Gesss sorry i don't know how i missed that caption!

Where's the egg on face smiley :oops:

_________________
Disappointment is an empty box full of expectation


Top
 Profile  
 
PostPosted: Sun Jan 17, 2010 8:00 am 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Fri Nov 02, 2007 9:49 am
Posts: 12971
Location: Ann Arbor, Michigan
First name: Hesh
Last Name: Breakstone
City: Ann Arbor
State: Michigan
Country: United States
Status: Professional
woodsworth wrote:

Where's the egg on face smiley :oops:


Sorry - I should have put it back where I found it.... :? :D

_________________
Ann Arbor Guitars


Top
 Profile  
 
PostPosted: Sun Jan 17, 2010 10:39 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Jun 22, 2005 10:11 am
Posts: 2761
Location: Tampa Bay
First name: Dave
Last Name: Anderson
City: Clearwater
State: Florida
Zip/Postal Code: 33755
Country: United States
This is so important to get that perfect glue joint
at the bridge. I used to use a separate sanding block with the top radius
the same as the guitar top or so I thought. There can be a slight difference so
this way is much better. Good tute Hesh. [:Y:]

_________________
Anderson Guitars
Clearwater,Fl. 33755


Top
 Profile  
 
PostPosted: Mon Jan 18, 2010 11:47 am 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Fri Nov 02, 2007 9:49 am
Posts: 12971
Location: Ann Arbor, Michigan
First name: Hesh
Last Name: Breakstone
City: Ann Arbor
State: Michigan
Country: United States
Status: Professional
Thanks Dave - hey I have to floss a bridge later today and now I have something to look at to tell me how.... :D

_________________
Ann Arbor Guitars


Top
 Profile  
 
PostPosted: Mon Jan 18, 2010 1:15 pm 
Offline
Contributing Member
Contributing Member

Joined: Wed Apr 23, 2008 7:16 pm
Posts: 146
Hey, Hesh,

How do you get the original radius on the bridge bottom?

Joe


Top
 Profile  
 
PostPosted: Mon Jan 18, 2010 1:47 pm 
Offline
Old Growth Brazilian Rosewood
Old Growth Brazilian Rosewood
User avatar

Joined: Fri Nov 02, 2007 9:49 am
Posts: 12971
Location: Ann Arbor, Michigan
First name: Hesh
Last Name: Breakstone
City: Ann Arbor
State: Michigan
Country: United States
Status: Professional
Hi Joe - what I did was laminate some wood together, in this case 6 pieces and then sand the top of the block in a 25' radius dish after making pencil lines all over the top of the block. When the lines are gone you are good-to-go. That transfers the dish's radius to the block. Cover with self stick sandpaper and you're done!

Attachment:
DSC02706.jpg


You do not have the required permissions to view the files attached to this post.

_________________
Ann Arbor Guitars


Top
 Profile  
 
PostPosted: Mon Jan 18, 2010 4:22 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Tue Jan 04, 2005 10:03 am
Posts: 6680
Location: Abbotsford, BC Canada
Something to note here is that Hesh is shaping the bottom of the bridge before he puts finish on the guitar.

It shouldn't make much difference if you do this after the finish is done (buffed out etc...) as a good finish should only be about 0.005" thick.

_________________
My Facebook Guitar Page

"There's really no wrong way, as long as the results are what's desired." Charles Fox

"We have to constantly remind ourselves what we're doing....No Luthier is putting a man on the moon!" Harry Fleishman

"Generosity is always different in the eye of the person who didn't receive anything, but who wanted some." Waddy Thomson



These users thanked the author Rod True for the post: Dmaxwell (Thu Jan 18, 2018 12:29 am)
Top
 Profile  
 
PostPosted: Mon Jan 18, 2010 8:29 pm 
Offline
Contributing Member
Contributing Member

Joined: Wed Apr 23, 2008 7:16 pm
Posts: 146
Thanks, Hesh1


Top
 Profile  
 
PostPosted: Thu Jan 21, 2010 10:41 pm 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Fri Jun 12, 2009 10:47 am
Posts: 192
First name: Adam
Last Name: Yavner
City: Wylie
State: TX
Zip/Postal Code: 75098
Country: USA
Focus: Build
Status: Amateur
Thanks Hesh, I plan to do this tomorrow so this is a great reference! I appreciate all your effort and helpful answers, as well as those I got from everyone in the thread that (i think) inspired this toot.

One thing I was going to do was trace an outline of my bridge in the proper location on the sandpaper, so that I can try to make sure and keep the bridge over the spot I am trying to match. Do you think this is a useful step?

One question - looks like you are using wax pencil - do you think that (or graphite) could have the potential to interfere wtih the glue if some remains in the pores? Just a thought.

Thanks again brutha!

adam

_________________
"Everyone wants to BE something, but nobody wants to BECOME something" - William Cumpiano


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 12 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 11 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com