Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 4:17 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 28 posts ]  Go to page 1, 2  Next
Author Message
PostPosted: Mon May 12, 2014 4:53 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
I've been working on this one for a while, and its got a few interesting features, so I thought I'd share it on here in case anyone's interested. It's a quilted maple/alpine spruce guitar with my own body shape - slightly wider than an OM with the waist shifted up to give more vibrating room in the lower bout. It's also got an adjustable neck, floating fingerboard extension, carbon buttress braces and carbon reinforced neck and heel. Its been challenging to say the least... :mrgreen:
Thanks to Todd Rose for the inspiration and advice [:Y:] (If he uses this forum?)
Anyway here's where I am so far...

Joining the top
Image

Rosette beginnings...
Image

Image

Image

Success! :D
Image

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
PostPosted: Mon May 12, 2014 4:59 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
Starting the neck. You can just see the ends of the 2 carbon tubes going down into the heel to stiffen it
Image

The neck side of the adjustable neck system
Image

Carbon rods and truss rod
Image

Neck carving
Image

Image

A bit of a different heel... :mrgreen:
Image

Image

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
PostPosted: Mon May 12, 2014 5:13 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
Side bending... I bend by hand on a hot pipe. I used supersoft 2 and it went ok - there was a bit of rippling here and there, but it should scrape out afterwards
Image

Installing the carbon butress braces
Image

A shot with an identical rosewood guitar I'm working on at the same time. You can get an idea of the headblock here... Basically, the heel is inset into a pocket in the guitar, so it can be adjusted without leaving a gap on the outside. There are 3 set screw in the block which correspond to the 3 metal inserts in the heel that adjust the angle of the neck up and down and side to side. The neck gets bolted on as normal.
Image

Fretboard routed for inlays
Image

And they're in...
Image

Image

Image

A mockup with the neck and body
Image

Looking like a guitar :D
Image

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
PostPosted: Mon May 12, 2014 11:11 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu May 12, 2005 5:46 am
Posts: 2931
Location: United States
That's looking great Peter!

_________________
Jim Watts
http://jameswattsguitars.com


Top
 Profile  
 
PostPosted: Tue May 13, 2014 7:20 am 
Offline
Cocobolo
Cocobolo
User avatar

Joined: Thu Oct 04, 2012 3:50 pm
Posts: 294
Location: Austria
First name: Michiyuki
Last Name: Kubo
State:
Country: Österreich
Status: Amateur
Lovely

_________________
久保
美智え


Top
 Profile  
 
PostPosted: Mon May 19, 2014 5:49 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
Made a bit of progress on this. I've finished the headstock overlay - I inlayed my name on it which was the first really intricate inlay I've done and it went fairly well. Thankfully it was in ebony, so it was easy to fill the gaps! I've also got all the linings on and started bracing the top. I'm using the same bracing pattern I used on my first that I copied from a picture of one of Somogyi's guitars. It's a very light X brace with lattice bracing on the lower bout and A frame upper bout bracing. The top is wonderful - master grade alpine spruce and rings like a bell :) I took it down to about 2.8mm and a bit thinner on the edges and lower bout and it still feels really stiff!

My logo before inlaying
Image

Headplate being glued up
Image

X brace getting glued up in the go bar deck
Image

Random curly shaving! :mrgreen:
Image

Bridge plate gluing and a few other braces laid in place
Image

More to come soon...

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
PostPosted: Sun Jun 08, 2014 4:20 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
So the top is braced and glued to the rims, and I'm just waiting for the LR Baggs Lyric pickup to arrive before I glue the back on. I want to test fit it beforehand so its easier to install.
Image

Image

Image

My ramshackle homemade spool clamps!
Image

Image

Test fitting the neck...
Image

The back inlay - spalted maple and rosewood. I haven't finished the twisty lines yet.
Image

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
PostPosted: Sun Jun 08, 2014 4:22 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
Please ignore the mess by the way - I'm not the tidiest of workers! :mrgreen:

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
PostPosted: Sun Jun 08, 2014 4:35 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Apr 08, 2009 9:34 am
Posts: 3081
Hey, you are not the only "messy" builder. Much prefer these kinds of photos to the "Guitar on Velvet with organized shavings" kind of photo...
There are times when building is messy, and times when it's time to clean the bench and get out the nice soft, clean rug.
Not my style, but looks like you are doing a fine job!


Top
 Profile  
 
PostPosted: Tue Jun 10, 2014 5:34 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
Thanks Haans! :)

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
PostPosted: Tue Jun 10, 2014 7:14 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Jan 13, 2010 12:46 am
Posts: 1247
First name: Beth
Last Name: Mayer
City: Tucson
State: AZ
Country: United States
Focus: Build
Status: Amateur
Petr, I love your aesthetic!!! I think your guitars rock :)


Top
 Profile  
 
PostPosted: Tue Jun 10, 2014 9:28 pm 
Offline
Koa
Koa

Joined: Sat Apr 19, 2008 10:08 pm
Posts: 1958
Location: Missouri
First name: Patrick
Last Name: Hanna
State: Missouri
Country: USA
Some real nice design elements there. Keep the progress pictures coming!


Top
 Profile  
 
PostPosted: Wed Jun 11, 2014 6:00 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Jul 05, 2013 12:57 pm
Posts: 903
Location: London, England
Focus: Build
Status: Amateur
Can't believe I missed this! Looking great, Peter!
I always get a bit jealous when I see your work! :lol:

I'd love to know how you put that neck blank together!


Top
 Profile  
 
PostPosted: Wed Jun 11, 2014 7:53 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
Thanks guys!
Nick, the neck blank is made up as normal, but I left it as long as the whole fretboard and glued the heel block on where the 14th fret was going. I cut the tenon on the heel block before gluing it on. I then bandsawed out the taper in the end and chiselled out the corner bits next to the tenon. Then rout the truss rod channel till it pokes out the bottom and continue the channel on the other side with chisels... Simple :mrgreen:
I adapted the idea from Todd Rose's guitars - he's got a thread on the AGF somewhere showing the whole process, only I used 2 smaller carbon tubes rather than one massive one to support the heel.
http://www.acousticguitarforum.com/foru ... 710&page=5

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars



These users thanked the author PeterF for the post: Nick Royle (Sat Jul 12, 2014 5:51 pm)
Top
 Profile  
 
PostPosted: Fri Jul 11, 2014 6:25 pm 
Offline
Walnut
Walnut

Joined: Mon Feb 11, 2013 11:24 pm
Posts: 16
First name: Jim
Last Name: Straight
City: Portland
State: Oregon
Focus: Build
Status: Amateur
I absolutely love the looks of the rosette and fret board together. How do you cut out sections of the sound board for the rosette?


Top
 Profile  
 
PostPosted: Sat Jul 12, 2014 5:40 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
Thanks Jim! I use a dremel in a homemade router base/circle cutter and cut the ends of each section with a knife and chisels.

So its been a while since I updated this. The back is on and end graft inlayed. I had a few delays trying to find a method of binding that would work for me. I tried all sorts of different types of tape and roping before finding out about fibre reinforced strapping tape - works amazingly well! So far I think its the best binding job I've done - not a single gap :D
On a bad note though, I have to re-do the fingerboard. I slotted it myself with a japanese pull saw and mitre box and I think the saw was too flexible or something because the slots aren't perfectly vertical and the frets are tipping slightly leaving gaps underneath. I can't think of any other reason for the gaps anyway - they're definitely deep enough.
I bought a pre-slotted board in the end in frustration and will be starting on that soon...
Oh and I've also roughed out the bridge.

Image

Image

Image

My simple binding router jig. It works pretty well...
Image

Image

Image

Image

Image

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
PostPosted: Sat Jul 12, 2014 5:55 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
Oh I forgot to show a picture of the back bracing. Its something a little different I got from looking at Tom Doerr's guitars. It seemed like it would help against the neck pulling upwards and flattening the back.

Image

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
PostPosted: Mon Sep 08, 2014 11:38 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
So its been rather a while since I updated this. I've been away and having a lot of trouble with the frets, but I've managed to get past it thankfully and its on to a new stage. I've got all the frets in, the fingerboard glued on and have been sanding the body for hours.
Those who look carefully will probably notice the fingerboard looks different and thats because I made a new one [xx(] There was a problem with the fret slots on the old one, so I bought a preslotted board and did it all again.

Image

Image

Image

Image

Image

Image

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
PostPosted: Mon Sep 08, 2014 7:58 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Jan 13, 2010 12:46 am
Posts: 1247
First name: Beth
Last Name: Mayer
City: Tucson
State: AZ
Country: United States
Focus: Build
Status: Amateur
Still watching and enjoying, Peter. Bit jealous of those Florentine binding chops!!!


Top
 Profile  
 
PostPosted: Tue Sep 16, 2014 10:28 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
Finishing time!! The first zpoxy pore fill coat has just gone on and it looked so good I had to put some pictures up! :D

Image

Image

Image

Image

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
PostPosted: Tue Sep 16, 2014 10:35 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Jan 13, 2010 12:46 am
Posts: 1247
First name: Beth
Last Name: Mayer
City: Tucson
State: AZ
Country: United States
Focus: Build
Status: Amateur
Wow....chatoyance!!!!


Top
 Profile  
 
PostPosted: Thu Sep 18, 2014 4:40 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Tue Mar 01, 2011 1:32 pm
Posts: 3470
First name: Alex
Last Name: Kleon
City: Whitby
State: Ontario
Zip/Postal Code: L1N8X2
Country: Canada
Focus: Build
Status: Amateur
I'll keep the verbage to a minimum. WOW!

Alex

_________________
"Indecision is the key to flexibility" .... Bumper sticker


Top
 Profile  
 
PostPosted: Thu Sep 18, 2014 9:11 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri May 18, 2012 8:35 pm
Posts: 2658
Location: Austin, Texas
First name: Dan
Last Name: Smith
City: Round Rock
State: TX
Zip/Postal Code: 78681
Country: USA
Focus: Build
Status: Amateur
Super-Duper!

_________________
wah
Wah-wah-wah-wah
Wah


Top
 Profile  
 
PostPosted: Thu Sep 18, 2014 9:55 pm 
Offline
Cocobolo
Cocobolo

Joined: Sat Jul 12, 2014 3:50 pm
Posts: 266
First name: Jeff
Last Name: Dillard
State: California
Focus: Build
Status: Amateur
Really like it,totally beautiful!!!


Top
 Profile  
 
PostPosted: Fri Sep 19, 2014 2:08 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jun 10, 2012 10:04 am
Posts: 773
First name: Peter
Last Name: Fenske
City: Leeds
State: Yorkshire
Country: Uk
Focus: Build
Status: Amateur
Thanks very much :) I was a little hesitant using such expensive wood at first, but the results are totally worth it!
A couple of coats of zpoxy later and the lacquering can begin...
Image

In my ultra high-tec spray booth... :D I'm spraying Bolgers nitro lacquer using a preval sprayer. So far (2 coats in on the neck) its going ok, although I don't have any other spraying experience, so I don't really know what ok is! Its leaves a fairly rough surface finish because it doesn't atomise the lacquer as well as a proper spray gun, but for the price, a little extra level sanding is well worth it. A unit costs around £15 here in Wales and you need about 2 refils (£8 each) to finish a guitar. You can also fill it with whatever finish you like and thin it to just the way you want it which makes it a lot better and cheaper than rattle cans.

Image

_________________
"I am always doing that which I cannot do, in order that I may learn how to do it."
Pablo Picasso

https://www.facebook.com/FenskeGuitars


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 28 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 9 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com