Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 3:31 pm


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 25 posts ] 
Author Message
 Post subject: Go-bar trouble
PostPosted: Mon May 06, 2019 7:52 am 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1323
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
I'm finally getting back to my build I started last year. I got a little off track but I'm ready to dive back in. First thing I did I screwed up. I've never used the deck I built and the bars are plow markers. They seem a little too stiff for this unless I cut them shorter.

Here's what happened. I'm working on the back brace installation and I glued the center line strip in place with HHG. When I came back to check on it I saw the strip looked like a snake. I'll either remove it or just soften the glue and try to realign it and clamp it again. I guess I should have clamped a couple of straight edges to form a channel but I didn't think it was necessary.

I have another back to do and I want to avoid this happening again. Are my bars too heavy? Should I use straight edges to keep it in place? I really thought this was going to be real easy using a go-bar deck. Oh well.

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 8:03 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3288
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
I use a 1/8" thick aluminum strip which is also held in place by go bars to hold the line.

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 8:20 am 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1323
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
Are these bars to stiff?

Attachment:
20190504_181652.jpg


You do not have the required permissions to view the files attached to this post.

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 8:27 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Feb 12, 2009 12:12 pm
Posts: 3290
First name: Bryan
Last Name: Bear
City: St. Louis
State: Mo
Country: USA
Focus: Build
Status: Amateur
Shortening the bars will not reduce their stiffness or decrease clamping pressure. For a given thickness the only way t reduce the force is to lengthen the bar by raising the deck height. For a given thickness, the force exerted by the bar does not increase much at all once it is bent past the buckling point. This seems counter intuitive but imagine holding a piece of uncooked spaghetti between your fingertips and compressing it. Now break it in half and try compressing it between your finger tips, now a fourth of the original length. As the spaghetti gets shorter you will find that it hurts your finger tips more before it buckles.

I use fiberglass driveway markers for my bars and they are stiffer than the 1/4" bars that are commonly used. Instead of a deck, I use my benchtop and the ceiling which has a much longer span. I end up with about the same amount of force per bar as the typical set-up.

_________________
Bryan Bear PMoMC

Take care of your feet, and your feet will take care of you.


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 8:33 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sun Mar 30, 2008 8:20 am
Posts: 5924
For the back graft I usually use epoxy glue. Because of the way the grain is oriented the pieces seemed to want to curl up and move around when I used water based glues. The other thing I do is wait a week or so after gluing the two back halves together before gluing on the back graft. I use water based glues to glue the back seam and I want the water to be gone before I glue the graft.


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 8:54 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Jul 27, 2015 8:21 am
Posts: 3288
First name: Brad
Last Name: Combs
Focus: Build
Status: Amateur
Your gobars seem fine, what is the red thing on the tip?


Sent from my iPhone using Tapatalk Pro

_________________
Insta - https://www.instagram.com/cbcguitars/
Facebook - https://www.facebook.com/cbcguitars


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 9:00 am 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1323
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
Just some plastic squares I use for glue removal. I used them to keep from marring the brace I used as a caul.

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!



These users thanked the author banjopicks for the post: bcombs510 (Mon May 06, 2019 9:15 am)
Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 9:55 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Aug 19, 2005 4:02 am
Posts: 3227
Location: The Woodlands, Texas
First name: Barry
Last Name: Daniels
I have some of those orange bars which are 5/16" fiberglass driveway markers from home despot. They are too stiff for most clamping. I only use them when I need additional clamp pressure. I do most brace glue ups with 3/16" fiberglass kite spars from Into-the-Wind. I love them. Just the right amount of pressure.


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 10:17 am 
Offline
Contributing Member
Contributing Member

Joined: Tue Dec 17, 2013 10:52 pm
Posts: 2953
First name: Don
Last Name: Parker
City: Charleston
State: West Virginia
Zip/Postal Code: 25314
Country: USA
Focus: Build
Status: Amateur
I think everyone else has addressed your original questions, so let me give you something else to worry about (sorry about this). The lower deck of your go-bar deck looks to be prone to deflection (and therefore deformation) under load. You would be shocked by how much deformation happens to a single 3/4" thick sheet of plywood when you put 20 go-bars in place. That problem is exacerbated by the fact that you are using go-bars that are stiffer than you need. In addition to getting better go-bars, I would have a torsion box for the lower deck. The upper deck can deflect and it is no big deal. Keep in mind that this is only a problem if you want the radii of the curves you are creating to actually be what you planned. The curves will be curved no matter what; but they might be a little different from what you wanted if you let the deformation happen.


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 10:29 am 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1323
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
Thanks Don, I am aware of those problems will rectify it at some point.

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 12:43 pm 
Offline
Koa
Koa

Joined: Fri Feb 24, 2017 8:43 am
Posts: 1700
For the back strip I don’t use my deck. Instead I simply use a strip of oak that is reasonably flat over the strip... then lay 2 35 lb dumbbells along it to clamp.


Sent from my iPhone using Tapatalk



These users thanked the author SnowManSnow for the post: banjopicks (Mon May 06, 2019 2:36 pm)
Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 2:05 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7219
First name: Ed
Last Name: Bond
City: Vancouver
Country: Canada
Focus: Build
Status: Professional
I also use a straight edge. Clamped in place with go bars, then I tilt the go bars on the back strip to push the back strip into/against the straightedge...


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 2:37 pm 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1323
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
SnowManSnow wrote:
For the back strip I don’t use my deck. Instead I simply use a strip of oak that is reasonably flat over the strip... then lay 2 35 lb dumbbells along it to clamp.


Sent from my iPhone using Tapatalk


I like that idea!

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 5:01 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Jul 10, 2009 4:44 am
Posts: 5398
First name: colin
Last Name: north
Country: Scotland.
Focus: Build
Status: Semi-pro
2/3 thicknesses masking tape each side keeps it in line and makes cleanup easy.
Hold it down with gobars and a 1/4" sapelle strip faced with cork and packing tape to prevent any glue sticking.

_________________
The name catgut is confusing. There are two explanations for the mix up.

Catgut is an abbreviation of the word cattle gut. Gut strings are made from sheep or goat intestines, in the past even from horse, mule or donkey intestines.

Otherwise it could be from the word kitgut or kitstring. Kit meant fiddle, not kitten.


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 7:38 pm 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1323
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
I was just double checking the plan for grain orientation and I noticed it calls for cross grain. I see this as meaning I will need to glue up some end cuts to get this. Is that right?

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Mon May 06, 2019 7:55 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7241
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
I usually just cut a strip off of the end of the top.

_________________
Steve Smith
"Music is what feelings sound like"


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Tue May 07, 2019 7:32 am 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1323
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
SteveSmith wrote:
I usually just cut a strip off of the end of the top.


Ah ha! Thanks for that tip Steve.

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Tue May 07, 2019 7:59 am 
Offline
Koa
Koa
User avatar

Joined: Sat Jan 19, 2013 7:33 am
Posts: 1831
First name: Willard
Last Name: Guthrie
City: Cumberland
State: Maryland 21502
Zip/Postal Code: 21502
Country: United State
Focus: Repair
Status: Semi-pro
Keep in mind that the pressure exerted by a go-bar or spring-bar is applied along the axis of the tips...even with a bar bent so that the tips are nearly flat on the work, the line of action will be on the line between those tips. With Titebond (which has low initial tack and tends to allow components to slither about with abandon until the glue line is well-thinned), keeping the tips of the bar aligned such that there is no side load will help with keeping things in one spot.

_________________
We have become a civilization that elevates idiots, prostitutes, and clowns. Am I still to defend it? Yes, for its principles. Yes, for what it was. Yes, for what it still may be.

-Mark Helprin, The Oceans and the Stars: A Sea Story, A War Story, A Love Story (A Novel)


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Tue May 07, 2019 8:39 am 
Offline
Koa
Koa
User avatar

Joined: Thu Jan 10, 2008 5:08 am
Posts: 1905
Location: Raleigh, NC
First name: Steve
Last Name: Sollod
Focus: Build
Status: Amateur
Rather than a go-bar deck, I made a simple vacuum clamp. The frame is covered in plastic. There is weather stripping under the frame. I sealed my radius dishes in epoxy so the weather stripping seals well. The pump is a medical grade vacuum pump from ebay and the fittings came from Joe Woodworker. I works well and doesn't take up a lot of room.


You do not have the required permissions to view the files attached to this post.

_________________
Steve Sollod (pronounced sorta like "Solid")
www.swiftcreekguitars.com


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Tue May 07, 2019 11:38 am 
Offline
Contributing Member
Contributing Member

Joined: Tue Jan 29, 2008 11:14 am
Posts: 819
First name: Tim
Last Name: Lynch
City: Santa Cruz
Zip/Postal Code: 95060
Country: United States
Focus: Build
Status: Amateur
Are you using a radiused dish for gluing up the center strip ?????
I ask because the in picture it looks like you are. With the cross grain in the strip and the removal of portions of that strip for your back braces that doesn't help trying to keep them in place much. I use a flat board with a straight edge to align the pieces for the back strip and I don't worry about leaving a small gap where my braces will go.



These users thanked the author Tim L for the post: banjopicks (Tue May 07, 2019 2:32 pm)
Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Tue May 07, 2019 1:08 pm 
Offline
Koa
Koa

Joined: Fri Feb 24, 2017 8:43 am
Posts: 1700
banjopicks wrote:
SnowManSnow wrote:
For the back strip I don’t use my deck. Instead I simply use a strip of oak that is reasonably flat over the strip... then lay 2 35 lb dumbbells along it to clamp.


Sent from my iPhone using Tapatalk


I like that idea!

A length of railroad tie also works great. Or at least a few shorter ones so it is manageable


Sent from my iPhone using Tapatalk


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Tue May 07, 2019 2:29 pm 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1323
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
I don't have any ties or dumb bells. I'll find something.

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Tue May 07, 2019 2:34 pm 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1323
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
Tim L wrote:
Are you using a radiused dish for gluing up the center strip ?????
I ask because the in picture it looks like you are. With the cross grain in the strip and the removal of portions of that strip for your back braces that doesn't help trying to keep them in place much. I use a flat board with a straight edge to align the pieces for the back strip and I don't worry about leaving a small gap where my braces will go.


Yes I was but I won't again.

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Thu May 09, 2019 8:12 am 
Offline
Koa
Koa
User avatar

Joined: Tue Feb 26, 2008 6:19 am
Posts: 1323
First name: Richard
Last Name: Hutchings
City: Warwick
State: RI
Zip/Postal Code: 02889
Country: United States
Focus: Build
Status: Amateur
I think I did better this morning. I used end cuts from a top I thinned too much. I also used a metal straight edge to align the pieces. After the HHG set up a little I moved the bars that were holding the straight edge onto the caul. I was going to use weights but this seems so easy.

Attachment:
Gluing the backstrip.jpg


You do not have the required permissions to view the files attached to this post.

_________________
Hutch

Get the heck off the couch and go build a guitar!!!!


Top
 Profile  
 
 Post subject: Re: Go-bar trouble
PostPosted: Thu May 09, 2019 1:52 pm 
Offline
Contributing Member
Contributing Member

Joined: Fri Jan 11, 2013 2:26 pm
Posts: 455
First name: Carl
Last Name: Dickinson
City: Forest Ranch
State: California
Zip/Postal Code: 95942
Country: USA
Focus: Build
Status: Amateur
Here's some pics of my go-bar deck. Don's point about torsion box describes what it has (think box beams in house construction). They are sized to an F clamp end so the deck can be used for other clamping operations and go-bar storage. I'm using 24" kite spars, 26" spacing between decks and cork on bottom surface of top deck to keep top end of go-bar from slipping. I block the radius dish up for gluing braces and have a 4" tall platform for flat gluing operations (should have made it 3"). Tops and backs are glued onto the sides in their mold (depending on the depth of the body, the go-bars can have quite an arc to them).


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 25 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: Mike Collins and 66 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com