Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 5:47 am


All times are UTC - 5 hours





Post new topic Reply to topic  [ 13 posts ] 
Author Message
PostPosted: Wed Aug 14, 2019 6:20 pm 
Offline
Koa
Koa

Joined: Fri Feb 10, 2017 11:09 pm
Posts: 870
Location: Cowichan Valley, BC, Canada
First name: Conor
Last Name: Searl
City: Duncan
State: British Columbia
Zip/Postal Code: V9L 2E5
Country: Canada
Status: Semi-pro
I need some perspective,

I've got an 80's Japanese Tele Custom reissue in for a setup. The truss rod adjuster is at the heel of the neck. The fret board is a gong show of divots and flat spots and the relief measures over .035". Pulling the neck off and checking to see how the truss rod moves, the nut is totally loose, which explains the huge amount of relief, however as I tighten the nut it tightens up pretty quickly.

In fact after screwing it as tight as I can get it, my notched straightedge shows the fret board to be pretty flat. The fret plane is still an adventure, there is still relief on the low E, but the high E has negative relief. So it seems I can dress this out and it will come out fine, but having the truss rod as tight as it will go seems like it doesn't leave much wiggle room for the future. But maybe this is just typical of older single action rods? I don't have as much experience with these kinds of rods.


Top
 Profile  
 
PostPosted: Wed Aug 14, 2019 6:26 pm 
Online
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5743
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
It just depends. I've had that happen on Fenders and Gibsons. I chalk it up to variances in installation procedures. I've found (as have others), that torqueing the truss rod back and forth from one extreme to the other sometimes loosens things up a bit. Your experiences may vary. Remember to let the truss rod sit for awhile, as the wood moves slower than the metal. I oftentimes let the neck sit overnight if the client isn't in a big rush.

_________________
"Act your age, not your shoe size" - Prince



These users thanked the author Chris Pile for the post: fumblefinger (Wed Aug 14, 2019 10:09 pm)
Top
 Profile  
 
PostPosted: Thu Aug 15, 2019 7:00 am 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Mon Dec 27, 2010 9:06 pm
Posts: 2739
Location: Magnolia DE
First name: Brian
Last Name: Howard
City: Magnolia
State: Delaware
Zip/Postal Code: 19962
Country: United States
Focus: Repair
Status: Professional
bend the neck back by hand over a sandbag or something while tightening the nut and you will be able to pull more out of it.

_________________
Brian

You never know what you are capable of until you actually try.

https://www.howardguitarsdelaware.com/



These users thanked the author B. Howard for the post: Conor_Searl (Thu Aug 15, 2019 10:51 am)
Top
 Profile  
 
PostPosted: Thu Aug 15, 2019 8:49 am 
Online
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5743
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
Quote:
bend the neck back by hand over a sandbag or something while tightening the nut and you will be able to pull more out of it.


Forgot to mention that trick. Good one, Mr. Howard!!!!

_________________
"Act your age, not your shoe size" - Prince



These users thanked the author Chris Pile for the post: Conor_Searl (Thu Aug 15, 2019 10:50 am)
Top
 Profile  
 
PostPosted: Thu Aug 15, 2019 9:05 am 
Offline
Koa
Koa

Joined: Wed Feb 17, 2016 8:54 am
Posts: 854
State: Texas
Country: United States
Focus: Repair
B. Howard wrote:
bend the neck back by hand over a sandbag or something while tightening the nut and you will be able to pull more out of it.


This. I use a long sanding beam with shims on the ends of the fretboard and add a few clamps in the middle. Let it sit for a while and then you can tighten the rod to hold it in an appropriate amount of overbow.



These users thanked the author DanKirkland for the post: Conor_Searl (Thu Aug 15, 2019 10:50 am)
Top
 Profile  
 
PostPosted: Thu Aug 15, 2019 9:19 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Fri Aug 19, 2005 4:02 am
Posts: 3227
Location: The Woodlands, Texas
First name: Barry
Last Name: Daniels
When the nut gets super tight real quickly, it may be bottoming out on the threads. If that is the issue, it is easy to fix by adding a thick washer under the nut.



These users thanked the author Barry Daniels for the post: Conor_Searl (Thu Aug 15, 2019 10:52 am)
Top
 Profile  
 
PostPosted: Thu Aug 15, 2019 10:51 am 
Offline
Koa
Koa

Joined: Fri Feb 10, 2017 11:09 pm
Posts: 870
Location: Cowichan Valley, BC, Canada
First name: Conor
Last Name: Searl
City: Duncan
State: British Columbia
Zip/Postal Code: V9L 2E5
Country: Canada
Status: Semi-pro
DanKirkland wrote:
B. Howard wrote:
bend the neck back by hand over a sandbag or something while tightening the nut and you will be able to pull more out of it.


This. I use a long sanding beam with shims on the ends of the fretboard and add a few clamps in the middle. Let it sit for a while and then you can tighten the rod to hold it in an appropriate amount of overbow.


This is way more elegant. Here I was all set to put the neck on the sandbag, one foot on the headstock and the other on the heel...
;)


Top
 Profile  
 
PostPosted: Thu Aug 15, 2019 11:18 am 
Offline
Koa
Koa

Joined: Fri Feb 10, 2017 11:09 pm
Posts: 870
Location: Cowichan Valley, BC, Canada
First name: Conor
Last Name: Searl
City: Duncan
State: British Columbia
Zip/Postal Code: V9L 2E5
Country: Canada
Status: Semi-pro
Barry Daniels wrote:
When the nut gets super tight real quickly, it may be bottoming out on the threads. If that is the issue, it is easy to fix by adding a thick washer under the nut.


I was wondering about that too. Dan Erlewine talks about that in one of his trade secrets videos. Its harder for me to tell with the adjuster in the heel than on a Gibson style rod, but I can see through the phillips crosshairs (?) in the nut that there is still quite a bit of thread.


Top
 Profile  
 
PostPosted: Thu Aug 15, 2019 11:29 am 
Offline
Koa
Koa

Joined: Fri Feb 10, 2017 11:09 pm
Posts: 870
Location: Cowichan Valley, BC, Canada
First name: Conor
Last Name: Searl
City: Duncan
State: British Columbia
Zip/Postal Code: V9L 2E5
Country: Canada
Status: Semi-pro
Funny, I was just asking about how frequently twisted necks come up a week or so ago.

After sleeping on it, and leaving the neck under tension over night trying to get it flat as Chris suggested then using the tricks mentioned above I can get it to read flat on the bass side, but when it reads flat there I end up with significant back bow on the treble side. Sighting down the neck from the heel I now see there is definitely a twist. I've got a lot of meat on the frets still, so I'll leave the neck at midway (slight relief on the bass side and pretty flat on the treble side) so as not to leave it cranked as hard as it will go and level and dress the frets. We can deal with the twist when its time for a re-fret.


Top
 Profile  
 
PostPosted: Thu Aug 15, 2019 11:52 am 
Online
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5743
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
Yeah - doesn't have to be perfectly flat for you to make it playable. In the past, I have put some bow on the bass side by milling off more fret height. I think you got this.

_________________
"Act your age, not your shoe size" - Prince



These users thanked the author Chris Pile for the post: Conor_Searl (Thu Aug 15, 2019 1:25 pm)
Top
 Profile  
 
PostPosted: Thu Aug 15, 2019 2:52 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7240
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
Also doesn't hurt to leave a bit more relief on the bass side then on the treble side. In fact that is the way I was taught and is how I do all of them.

_________________
Steve Smith
"Music is what feelings sound like"


Top
 Profile  
 
PostPosted: Thu Aug 15, 2019 4:04 pm 
Online
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5743
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
Quote:
Also doesn't hurt to leave a bit more relief on the bass side then on the treble side. In fact that is the way I was taught and is how I do all of them.


True, but sometimes the guitar has other ideas.

_________________
"Act your age, not your shoe size" - Prince


Top
 Profile  
 
PostPosted: Thu Aug 15, 2019 5:26 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7240
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
Chris Pile wrote:
Quote:
Also doesn't hurt to leave a bit more relief on the bass side then on the treble side. In fact that is the way I was taught and is how I do all of them.


True, but sometimes the guitar has other ideas.


No argument there.

_________________
Steve Smith
"Music is what feelings sound like"


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 13 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 11 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com