Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Mar 28, 2024 7:04 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 8 posts ] 
Author Message
PostPosted: Thu Sep 16, 2021 1:45 pm 
Offline
Walnut
Walnut

Joined: Mon Jan 04, 2021 6:35 pm
Posts: 12
Location: alabama
First name: STEVE
Last Name: LEONARD
State: AL
Zip/Postal Code: 36312
Country: United States
Focus: Build
Status: Amateur
Ok did a search and could not fine a suitable answer.......I'm using an open scale length of 21.375" for the guitar I'm building. What sort of tolerance do I have with that? I am trying to put the bridge plate in the right place! I have a finger board slotted for that scale.

Thanks!

_________________
Steve Leonard
SEleonard


Top
 Profile  
 
PostPosted: Thu Sep 16, 2021 2:10 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7240
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
Check out the StewMac Fret Scale Calculator. You can plug in scale length and other info then it will calculate the compensated lengths to the center of the saddle for the high and low E strings. You can use that length to determine where the saddle and, therefor, the bridge must go. That will let you place the bridge plate. I try to keep my measurements using rulers to +/- 0.01" since that's the best I can see with my optivisor.

_________________
Steve Smith
"Music is what feelings sound like"


Top
 Profile  
 
PostPosted: Thu Sep 16, 2021 2:15 pm 
Offline
Contributing Member
Contributing Member

Joined: Tue Dec 17, 2013 10:52 pm
Posts: 2953
First name: Don
Last Name: Parker
City: Charleston
State: West Virginia
Zip/Postal Code: 25314
Country: USA
Focus: Build
Status: Amateur
Here is a pretty handy guide:

https://www.stewmac.com/fret-calculator/

Once you use the calculator, look to the bottom for info on bridge placement. From that info, you should be able to figure out where to put the bridge plate.

EDIT--

Duplication of Steve's post.


Top
 Profile  
 
PostPosted: Thu Sep 16, 2021 3:06 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5743
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
Define tolerance. For what?

_________________
"Act your age, not your shoe size" - Prince


Top
 Profile  
 
PostPosted: Thu Sep 16, 2021 3:23 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Tue May 13, 2008 10:44 am
Posts: 6232
Location: Virginia
For a bridge plate you should have plenty of tolerance. I would aim to put the saddle at 21.475 and make the bridge plate extend 1/8th inch wider than your bridge. That will give you plenty of fudge factor.


Top
 Profile  
 
PostPosted: Thu Sep 16, 2021 4:02 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Thu May 12, 2005 5:46 am
Posts: 2931
Location: United States
Like JF I make my bridge plates a little bigger than the bridge so they extend a little in front and behind the bridge.

_________________
Jim Watts
http://jameswattsguitars.com


Top
 Profile  
 
PostPosted: Sat Sep 18, 2021 2:19 pm 
Offline
Cocobolo
Cocobolo

Joined: Fri Mar 15, 2013 5:31 am
Posts: 219
First name: Bob
Last Name: Orr
Focus: Build
Status: Amateur
buzzleo wrote:
Ok did a search and could not fine a suitable answer.......I'm using an open scale length of 21.375" for the guitar I'm building. What sort of tolerance do I have with that? I am trying to put the bridge plate in the right place! I have a finger board slotted for that scale.

Thanks!



Do you mean the bridge on top of the guitar or the bridge plate inside the guitar, not the same thing.


Top
 Profile  
 
PostPosted: Tue Sep 21, 2021 7:34 pm 
Offline
Koa
Koa
User avatar

Joined: Tue Oct 30, 2007 9:13 am
Posts: 1167
Location: United States
State: Texas
Focus: Repair
Status: Professional
You have very little tolerance on a guitar with that short of a scale. The shorter the scale the more important the compensation will be, so study it out and set the bridge exactly. Take your time!

_________________
https://www.facebook.com/profile.php?id=100008907949110


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: John Steele and 49 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com