Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Mon Mar 18, 2024 11:39 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 16 posts ] 
Author Message
 Post subject: My Entry Lap Steel
PostPosted: Thu Mar 14, 2013 4:25 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Feb 25, 2013 4:34 pm
Posts: 223
First name: Kent
Last Name: Wilkinson
City: New Carlisle
State: Ohio
Zip/Postal Code: 45344
Country: USA
Focus: Build
I have been working on it a few weeks. I made a template of a explorer but I downsized it. 22.5 inch scale. Traced onto a poplar plank 2 inch thick. Then onto the band saw. I picked up a piece of 1/4 inch Zebro Wood for the fret board. The fret board was the scairest part for me :shock: . I put it off then just jumped in and did it. It was probably the easest part so far. I had a Stew-Mac fret jig, saw and template. Went really smooth. The hardest part for me has been cutting the head stock angle. I used a small hand saw on both sides then then leveled it with a hand plane. There has been tons of sanding and there is still allot left. My spindle sander make it easy to do the sides. I have the fret board glued on. I ordered Gibson tuners since it's a Explorer from Sam Ash. I also ordered the jack plate, Bone for the nut, Bridge. I had a Kent Armstrong Jazz Humbucker that some one had me replace with something else. He gave me the pick up when I was done. I have some some car paint left over from a restoration project that I might use. The bone nut I ordered isn't wide enough. I am trying to come up with a idea of something else I can use as a nut blank. I thought about buying a pin turning blank and cutting it down. I'm a little tight on cash. The Break down is below of How much I spent so far. I might buy a maple dowel rod and slice off pieces for the and just do dots. Does anybody have any idea I can use for the fret board markers for some one on a budget? This is my first build so I am trying to be creative, but am a little lost. I'm thanking I can come in about $120.00. Maybe.

Bridge from China $6.95 ( Amazon )
Poplar about 3 bd ft $7.50 Local Store
Zebra Wood for Fret Board $3.00 Local store remnant
Gibson Tuner $59.00 ( Sam Ash )
Jack Plate $6.95 ( Sam Ash )
Pick up Free


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Thu Mar 14, 2013 4:28 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Feb 25, 2013 4:34 pm
Posts: 223
First name: Kent
Last Name: Wilkinson
City: New Carlisle
State: Ohio
Zip/Postal Code: 45344
Country: USA
Focus: Build
Template pictures below.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Thu Mar 14, 2013 4:51 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Mar 06, 2011 12:04 am
Posts: 5739
First name: Chris
Last Name: Pile
City: Wichita
State: Kansas
Country: Good old US of A
Focus: Repair
Status: Professional
Diggin' it so far!

_________________
"Act your age, not your shoe size" - Prince


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Thu Mar 14, 2013 6:32 pm 
Offline
Cocobolo
Cocobolo

Joined: Tue Oct 16, 2012 1:23 am
Posts: 262
First name: nick
Last Name: dingle
Focus: Build
Status: Amateur
Cool.


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Fri Mar 15, 2013 10:20 pm 
Offline
Mahogany
Mahogany

Joined: Thu Jun 07, 2012 3:17 pm
Posts: 78
First name: Randy
Last Name: Jones
City: Santa Clara
State: CA
Zip/Postal Code: 95050
Country: United States
Focus: Build
Status: Amateur
Yessir, I do want to build a lap steel someday. Great addition to the challenge!


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Sun Mar 17, 2013 6:04 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Feb 25, 2013 4:34 pm
Posts: 223
First name: Kent
Last Name: Wilkinson
City: New Carlisle
State: Ohio
Zip/Postal Code: 45344
Country: USA
Focus: Build
I inlayed the fret slots with maple today. I am happy with the results. I just need to figure out what to inlay for the position markers.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Sun Mar 17, 2013 6:26 pm 
Offline
Contributing Member
Contributing Member

Joined: Sat Feb 19, 2011 7:44 pm
Posts: 1225
Location: Andersonville
State: Tennessee
Country: USA
Focus: Build
Status: Professional
Might have to do one of these. Were expecting David Lindley's solo from Jackson Browns Redneck Friend on your video laughing6-hehe


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Sun Mar 17, 2013 6:40 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Feb 25, 2013 4:34 pm
Posts: 223
First name: Kent
Last Name: Wilkinson
City: New Carlisle
State: Ohio
Zip/Postal Code: 45344
Country: USA
Focus: Build
Actualy I don't know how to play one. Lol. I will probably get one of my Dobro playing friends to play it for the video.


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Thu Apr 04, 2013 3:22 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Feb 25, 2013 4:34 pm
Posts: 223
First name: Kent
Last Name: Wilkinson
City: New Carlisle
State: Ohio
Zip/Postal Code: 45344
Country: USA
Focus: Build
I was wanting to do one large inlay at the 12th fret. So I cut the ivory out today. It looks too big and off ballance being this big. What do you think? I and thinking about making a new one about half the size and maybe putting a ebony peg head overlay on and inlaying this one on the head stock. I layed the on to see what they look like.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Thu Apr 04, 2013 4:12 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Dec 21, 2012 11:52 am
Posts: 1388
First name: Zeke
Last Name: McKee
City: Goodlettsville
State: TN
Zip/Postal Code: 37070
Country: United States
Focus: Build
Status: Amateur
I think it would look nice on the headstock. It's a little large for the fretboard for my tastes.


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Fri Apr 05, 2013 6:00 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Feb 25, 2013 4:34 pm
Posts: 223
First name: Kent
Last Name: Wilkinson
City: New Carlisle
State: Ohio
Zip/Postal Code: 45344
Country: USA
Focus: Build
I think your right. I will use on the head stock. I am going to do something different on the fret board.


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Sat May 18, 2013 9:48 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Feb 25, 2013 4:34 pm
Posts: 223
First name: Kent
Last Name: Wilkinson
City: New Carlisle
State: Ohio
Zip/Postal Code: 45344
Country: USA
Focus: Build
I have been on hold do to lack of funds. Friday I will order the tuner hole jig. So she be making progress this week end.


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Sun Jul 28, 2013 8:12 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Feb 25, 2013 4:34 pm
Posts: 223
First name: Kent
Last Name: Wilkinson
City: New Carlisle
State: Ohio
Zip/Postal Code: 45344
Country: USA
Focus: Build
Progress up date.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Wed Jul 31, 2013 7:03 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Feb 25, 2013 4:34 pm
Posts: 223
First name: Kent
Last Name: Wilkinson
City: New Carlisle
State: Ohio
Zip/Postal Code: 45344
Country: USA
Focus: Build
More on my Lap Steel build. I carved out the pick up cavity today. Used a mallet and wood chisel. Getting closer. I need to buy a set of forstener bits to drill out the cavity for the volume pot. Playing catch up.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Wed Aug 07, 2013 6:52 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Feb 25, 2013 4:34 pm
Posts: 223
First name: Kent
Last Name: Wilkinson
City: New Carlisle
State: Ohio
Zip/Postal Code: 45344
Country: USA
Focus: Build
Bought a set of Forstner bits from harbor freight. So saturday I am planning on drilling out the rear of the body for the volume pot. [:Y:] Will post pictures after. Still having a hard time trying to decide on haw to make a nut.


Top
 Profile  
 
 Post subject: Re: My Entry Lap Steel
PostPosted: Sun Aug 11, 2013 6:53 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Feb 25, 2013 4:34 pm
Posts: 223
First name: Kent
Last Name: Wilkinson
City: New Carlisle
State: Ohio
Zip/Postal Code: 45344
Country: USA
Focus: Build
Carved out the rear body cavity for the volume pot and installed it. Took apart a small flood light bulb and removed the lense. I am going to use it for the rear cavity cover. I will install a small LED in the cavity that will come on when the guitar is plugged in. I need to buy a 1/4 inch jack plug and drill it out then I can wire it. Really close to being ready to play. The last 2 pictures are of my helper. Pictures won't load. Will try again later.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 16 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com