End mill bits for Inlay work

Board index » Luthiers Forum Rooms » Guitar Building Forum

All times are UTC - 5 hours

Forum rules

Be nice, no cussin and enjoy!

End mill bits for Inlay work

Page 1 of 1

[ 7 posts ]

Print view

Previous topic | Next topic

Author

Message

dofthesea

Post subject: End mill bits for Inlay work

Posted: Tue Apr 16, 2019 1:33 pm

Contributing Member

Joined: Sat Sep 14, 2013 9:46 pm
Posts: 413
Location: Napa Valley
First name: David
Last Name: Foster
State: CA
Zip/Postal Code: 94558
Country: USA
Focus: Build
Status: Amateur

Where is everyone getting the best quality for the best prices these days. Its been so long since I ordered them I dont remember the who from. Mostly for Dremel and Forstner tool

_________________
https://www.instagram.com/dofthesea/
https://www.facebook.com/PuraVidaUkuleles/

Top

Casey Cochran

Post subject: Re: End mill bits for Inlay work

Posted: Tue Apr 16, 2019 1:59 pm

Contributing Member

Joined: Thu Oct 07, 2010 5:28 pm
Posts: 645
First name: Casey
Last Name: Cochran
City: Gainesville
State: GA
Zip/Postal Code: 30501
Country: USA
Focus: Build

The last ones I bought were Monster Mills from Fastenal, I think about $6 each.

_________________
Good judgement comes from experience. Experience comes from poor judgement.

Top

phavriluk

Post subject: Re: End mill bits for Inlay work

Posted: Tue Apr 16, 2019 4:57 pm

Cocobolo

Joined: Mon Feb 13, 2012 8:49 pm
Posts: 286
First name: peter
Last Name: havriluk
City: granby
State: ct
Zip/Postal Code: 06035
Country: usa
Focus: Build
Status: Amateur

Dave Nichols (Custom Pearl Inlay) has them listed in his catalog.

_________________
Peter Havriluk

Top

Tim Mullin

Post subject: Re: End mill bits for Inlay work

Posted: Tue Apr 16, 2019 5:41 pm

Koa

Joined: Wed Jan 14, 2009 3:14 am
Posts: 649
Location: Shefford, Québec
First name: Tim
Last Name: Mullin
City: Shefford
State: QC
Zip/Postal Code: J2M 1R5
Country: Canada
Focus: Build
Status: Professional

Precision Bits : http://www.precisionbits.com

Sent from my iPad using Tapatalk

Top

dzsmith

Post subject: Re: End mill bits for Inlay work

Posted: Wed Apr 17, 2019 9:10 pm

Contributing Member

Joined: Fri May 18, 2012 8:35 pm
Posts: 2407
Location: Austin, Texas
First name: Dan
Last Name: Smith
City: Round Rock
State: TX
Zip/Postal Code: 78681
Country: USA
Focus: Build
Status: Amateur

I buy them from China thru Amazon. Around $10 for 10 pieces.
Larry Robinson suggested in his book to grind 1/16” off the end of old bits since only the tip gets worn.
I have not tried it yet.
I bought the stew mac bits, they were expensive and lasted a long while.

_________________
wah
Wah-wah-wah-wah
Wah

Top

Dave Livermore

Post subject: Re: End mill bits for Inlay work

Posted: Wed Apr 17, 2019 10:04 pm

Koa

Joined: Sun Sep 16, 2007 1:27 pm
Posts: 630
Location: United States

I get mine for free from my dentist.

(Really. No kidding, And they last for ever)

Top

dofthesea

Post subject: Re: End mill bits for Inlay work

Posted: Thu Apr 18, 2019 10:02 am

Contributing Member

Thanks for the info. I found another supplier through another forum. On ebay its. https://www.ebay.com/sch/m.html?_ssn=drillman1&_sop=10

Ends up being about $2-3$ per bit

_________________
https://www.instagram.com/dofthesea/
https://www.facebook.com/PuraVidaUkuleles/

Top

Page 1 of 1

[ 7 posts ]

Board index » Luthiers Forum Rooms » Guitar Building Forum

All times are UTC - 5 hours

Who is online

Users browsing this forum: No registered users and 10 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:

Official Luthiers Forum!

Forum rules

End mill bits for Inlay work

Who is online