Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Oct 31, 2024 6:38 pm


All times are UTC - 5 hours





Post new topic Reply to topic  [ 2 posts ] 
Author Message
PostPosted: Sun Aug 09, 2015 7:09 am 
Offline
Contributing Member
Contributing Member

Joined: Thu Mar 05, 2009 11:12 am
Posts: 147
First name: robin
Last Name: courtenay
City: andover
State: hants
Country: uk
Focus: Build
Status: Amateur
This is the first time i've used this jig, so i thought i'd post this attempt at a tut as i couldn't find any on the web when i was thinking about buying it. I'm using a dummy deck and body as a trial run as advised in the manual and will be cutting a dovetail joint. I'll have to do this in two or three parts due to the 8 attachment limit.
This first picture is the edge vice which clamps to the guitar body and the alignment template which locates on two pins on the other side of the vice, the two black thumb screws at the top of the vice are adjustable so as to allow you to square up the alignment template with the guitar body.
Attachment:
DSC_0374-1.jpg

These are the dummy neck and body
Attachment:
DSC_0376-1.jpg

The vice with the alignment template is clamped to the body and lined up with the centre line and top of the body.
Attachment:
DSC_0378-1.jpg

When all is squared up remove the alignment template and replace with the dovetail template, it is now ready for routing.
Attachment:
DSC_0381-1.jpg

Now we need to set the dial indicator bar to the correct height so that the tip of the dial indicator lines up with the proposed saddle position on the body. Place the edge vice and body onto the jig. The edge vice locates on two pins on the jig, undo the wing nut that clamps the bar and set at the saddle height and tighten the wing nut.
Attachment:
DSC_0382-1.jpg

The neck clamps to the neck plate and is located on two pins which fit into the truss rod slot, we must zero the dial indicator with the neck plate so that we can add the desired measurement above the saddle position when we adjust the neck angle later. To zero the dial indicator we use a straight edge with two holes for the truss rod pins and a line drawn through the centre this is clamped to he neck plate.
Attachment:
DSC_0385-1.jpg

We must make sure that tip of the dial indicator lines up with the centre line drawn on the straight edge (in the manual it says undo the wing nut and move the bar side to side to align with centre line,i could find no way of doing this as the bar always clamped in the same place, but as luck would have it was on the line anyway).
Attachment:
DSC_0386-1.jpg

Now we zero the dial to do this we loosen the screw that hold it and move it in or out until the the small dial needle is on one of the major numbers ,in this case it is on 0 but it could be any number,then tighten the screw. Next we rotate the outside ring until the large needle reads zero, the dial indicator is now set to the same plane as the neck plate.
Attachment:
DSC_0387-1.jpg
That's it for now, hope everything's clear, be back with part 2 shortly,all the best Roby.


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Sun Aug 09, 2015 2:15 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri May 18, 2012 8:35 pm
Posts: 2659
Location: Austin, Texas
First name: Dan
Last Name: Smith
City: Round Rock
State: TX
Zip/Postal Code: 78681
Country: USA
Focus: Build
Status: Amateur
That's a complicated tool but looks to be precise.
I would flip the alignment window so the scratched line is against the wood to minimize parallax error.
Thanks for sharing!
Dan

_________________
wah
Wah-wah-wah-wah
Wah


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com