Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Wed Aug 13, 2025 10:25 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 17 posts ] 
Author Message
PostPosted: Sun Sep 23, 2012 1:25 pm 
Offline
Mahogany
Mahogany

Joined: Wed Oct 05, 2011 12:36 pm
Posts: 78
Location: West Plains MO
First name: Cecil
Last Name: Carroll
City: West Plains
State: Missouri
Zip/Postal Code: 65775
Country: USA
Focus: Build
Status: Semi-pro
I recently had a failure with Rock hard varnish. This is after several successes. I just can't figure out where the process went wrong.

The real mystery is that while the finish on the bodies will not polish out, the necks, that were finished out of the same batch of thinned finish, turned out perfectly. I prepared the finish in the usual manner,applied finish to the bodies and then to the necks.

Any Ideas? I'm totally stumped.

cecil


Top
 Profile  
 
PostPosted: Sun Sep 23, 2012 2:57 pm 
Offline
Cocobolo
Cocobolo

Joined: Wed Dec 22, 2010 12:49 pm
Posts: 273
First name: Victor
Last Name: Seal
City: Osseo
State: MI
Zip/Postal Code: 49266
Country: USA
Focus: Build
Status: Amateur
When you state that a finish failed, could you be more specific? What did the product do or not do? Pals, Vic.


Top
 Profile  
 
PostPosted: Sun Sep 23, 2012 3:52 pm 
Offline
Contributing Member
Contributing Member

Joined: Tue Nov 21, 2006 4:02 pm
Posts: 801
Location: United States
First name: Gene
Last Name: Zierdt
City: Sebastopol
State: CA
Zip/Postal Code: 95472
Country: USA
Focus: Build
Status: Amateur
Was there any difference at all in surface prep between the neck and body?
ie, epoxy or other pore fill on body but not on neck? Any difference in application
technique?

And as Vic said, exactly what is "failure". Surface still tacky, bubbles, ???

_________________
Gene

Politicians and diapers must be changed often, and for the same reason- Mark Twain


Top
 Profile  
 
PostPosted: Sun Sep 23, 2012 6:34 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Jan 06, 2011 6:08 pm
Posts: 2712
First name: ernest
Last Name: kleinman
City: lee's summit
State: mo
Zip/Postal Code: 64081
Country: usa
Focus: Build
Status: Professional
I/m taking a wild guess but did you use rock hard when it was over 60% humidity? I/ve been to w, plains. (vy humid) I would only use varnish, when the humidity was under 50% did you brush or spray?? it could be any number of minor culprits.


Top
 Profile  
 
PostPosted: Sun Sep 23, 2012 6:34 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Thu Jan 06, 2011 6:08 pm
Posts: 2712
First name: ernest
Last Name: kleinman
City: lee's summit
State: mo
Zip/Postal Code: 64081
Country: usa
Focus: Build
Status: Professional
I/m taking a wild guess but did you use rock hard when it was over 60% humidity? I/ve been to w, plains. (vy humid) I would only use varnish, when the humidity was under 50% did you brush or spray?? it could be any number of minor culprits.


Top
 Profile  
 
PostPosted: Mon Sep 24, 2012 8:32 am 
Offline
Mahogany
Mahogany

Joined: Wed Oct 05, 2011 12:36 pm
Posts: 78
Location: West Plains MO
First name: Cecil
Last Name: Carroll
City: West Plains
State: Missouri
Zip/Postal Code: 65775
Country: USA
Focus: Build
Status: Semi-pro
The finish on the bodies simply will not buff our to anything close to an acceptable gloss. They look like I sanded to about 2000 grit and quit. I actually went to a 4000 grit abralon pad with an ROS. The results are blotchy and dull. The necks are as good as it gets.

The application was with the same brush out of the same container of mixed finish and thinner. I applied finish to the two bodies first and then the necks. Re coated within the hour for each successive coat. It's a mystery to me.

cecil


Top
 Profile  
 
PostPosted: Mon Sep 24, 2012 8:36 am 
Offline
Koa
Koa

Joined: Mon Oct 17, 2011 4:10 pm
Posts: 792
First name: Bob
Last Name: Gramann
City: Fredericksburg
State: VA
Zip/Postal Code: 22408
Country: USA
Focus: Build
Status: Professional
What's the wood on the body? Oil-based varnishes sometimes won't harden on oily woods like rosewood.


Top
 Profile  
 
PostPosted: Mon Sep 24, 2012 8:44 am 
Offline
Mahogany
Mahogany

Joined: Wed Oct 05, 2011 12:36 pm
Posts: 78
Location: West Plains MO
First name: Cecil
Last Name: Carroll
City: West Plains
State: Missouri
Zip/Postal Code: 65775
Country: USA
Focus: Build
Status: Semi-pro
The wood is osage orange on one and sapele on the other. I have used this finish on both before with good results.

Some one ask about humidity earlier. It was 45%.

cecil


Top
 Profile  
 
PostPosted: Mon Sep 24, 2012 9:18 am 
Offline
Koa
Koa

Joined: Mon Oct 17, 2011 4:10 pm
Posts: 792
First name: Bob
Last Name: Gramann
City: Fredericksburg
State: VA
Zip/Postal Code: 22408
Country: USA
Focus: Build
Status: Professional
Those woods shouldn't be any problem. Got me.


Top
 Profile  
 
PostPosted: Mon Sep 24, 2012 9:22 am 
Offline
Contributing Member
Contributing Member

Joined: Sun Jan 27, 2008 4:10 pm
Posts: 2764
First name: Tom
Last Name: West
State: Nova Scotia
Country: Canada
Focus: Build
Status: Amateur
Cecil: One post asked about different pore fill...................????
Tom

_________________
A person who has never made a mistake has never made anything!!!


Top
 Profile  
 
PostPosted: Tue Sep 25, 2012 7:58 am 
Offline
Mahogany
Mahogany

Joined: Wed Oct 05, 2011 12:36 pm
Posts: 78
Location: West Plains MO
First name: Cecil
Last Name: Carroll
City: West Plains
State: Missouri
Zip/Postal Code: 65775
Country: USA
Focus: Build
Status: Semi-pro
Tom
The pore filler was Zpoxy. I've used it forever and not had a problem with this finish.


cecil


Top
 Profile  
 
PostPosted: Tue Sep 25, 2012 8:30 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Tue Oct 12, 2010 9:01 pm
Posts: 3031
First name: Tony
Last Name: C
City: Brooklyn
State: NY
Focus: Build
Status: Amateur
That's a strange problem. Maybe there was some contamination on the wood from stearates in the sandpaper? Did you use the same paper for everything?

_________________
http://www.CostaGuitars.com
PMoMC


Top
 Profile  
 
PostPosted: Fri Sep 28, 2012 1:56 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sat Jan 15, 2005 12:50 pm
Posts: 3933
Location: United States
I've never re-coated on that short a schedule, and I wonder if, perhaps, that has something to do with it? Maybe the finish just has not had a chance to cure all the way through.

When I first started using Rockhard varnish, I was thinning it with paint store mineral spirits. I did have some issues with it hardening slowly, and not polishing out right. Eventually it refused to harden at all, and when I looked in the can there was a white precipitate in the bottom. Since then I've used only their proprietary reducer for thinning, and have had no more problems of that sort.


Top
 Profile  
 
PostPosted: Fri Sep 28, 2012 7:29 pm 
Offline
Koa
Koa
User avatar

Joined: Fri Jun 22, 2007 11:14 am
Posts: 1050
Location: Newland, North Carolina
First name: Dave
Last Name: Ball
It's strange that it seems right on one surface and not right on another, but I've had it with Rockhard. Something has changed. I used to have consistently good results with it, but the past couple of batches I've gotten have had big time problems both with hardening and with "grittiness" of texture. I recently had to strip the finish off of an archtop that I had attempted to finish with Rockhard (redid it in french polish and all is well). For me, that was it. I've moved on to Pratt and Lambert #38, and at least for now that's working very well.

I don't know what they did to Rockhard, but for a finish that I relied on for a long time, it suddenly became a problem and I'll not be using it any more.

Dave


Top
 Profile  
 
PostPosted: Sat Sep 29, 2012 9:49 am 
Offline
Mahogany
Mahogany

Joined: Wed Oct 05, 2011 12:36 pm
Posts: 78
Location: West Plains MO
First name: Cecil
Last Name: Carroll
City: West Plains
State: Missouri
Zip/Postal Code: 65775
Country: USA
Focus: Build
Status: Semi-pro
Al I used the proprietary reducer along withe the acetone and kerosene you recommend. It may have been that I re coated too soon. The process of applying the finish to two bodies delayed the application to the necks so that it was longer than an hour between coats.

I'm also wondering if some of the solvents may have had time to evaporate out by the time I got to the necks add the resulting in a thicker film.

Dave I'll check into Pratt and Lambert #38. I think I can get it locally through the Shirwin Williams store. If so it will save me a 100 mile trip to obtain more rockhard.

cecil


Top
 Profile  
 
PostPosted: Sun Sep 30, 2012 11:23 am 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Sat Jan 15, 2005 12:50 pm
Posts: 3933
Location: United States
As far as I can tell, the 'Rockhard' I'm getting now works the same as what I have been using all along, if not a little better. I can dream that I'm getting better at using it, of course...


Top
 Profile  
 
PostPosted: Sun Sep 30, 2012 12:37 pm 
Offline
Koa
Koa

Joined: Mon Jun 30, 2008 1:06 am
Posts: 508
First name: Greg
Last Name: B
City: Los Angeles
State: California
Quote:
Re coated within the hour for each successive coat. It's a mystery to me.


There's your problem! With Rockhard varnish, I've found that it's best to do one coat per day. Two coats a day is pushing it and can lead to the underlying coats not drying. Re coating after an hour??? No way that is going to work. It's not lacquer, and needs exposure to air to cure. By recoating too soon, you essentially seal in wet varnish. I found this out the hard way myself a long time ago.

I've never had a problem using mineral spirits to thin, but I accept that I could just be lucky. I've probably applied at least several gallons of the stuff in my life, so I'm not inexperienced. Frankly, I typically use it straight out of the can, except for the last coat, which is thinned slightly with turpentine to improve flow out. This extends the dry time but results in a very smooth final coat.

It hasn't been mentioned but I find the ambient temperature is very important with this varnish. Around 70 deg is best. If it's too cold, it takes forever to dry. If it's too hot, it doesn't flow out as smoothly and will need more leveling.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 17 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: dofthesea and 28 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com